| Stock Number and Description |
Model |
Year |
5804
#2 BOYAR SCHULTZ DUAL SPINDLE, 18” X 20” TABLE, OSCILLATING SPD’S, COLLET TYPE, 1968 |
#2 |
1968 |
5582
100 KVA SCIAKY MODEL EPKDE-1-15-100-12-16, 12” THROAT, 440 V, ROBOTRON CONTROLS |
EPKDE 1-15-100-12-16 |
|
6295
2 1/8” MODERN 2L, 20’ MAGAZINE BAR FEED, 2 SLIDES, TOOLING, 1983 (6295) |
2L |
1983 |
6306
BOOMERANG CONVEYOR |
N/A |
|
6305
MORBEDELLI MODEL U 60 |
U 60 |
|
6304
MORBEDELLI MODEL U 60 |
U 60 |
|
6303
NEWMAN POD PRESS |
N/A |
|
6334
MORBIDELLI J20 DOWEL INSERTER (6334) |
J20 |
|
6345
PIN ROUTER |
N/A |
|
6348
MEBER RESAW |
N/A |
|
6349
DIEHL SPLICER |
N/A |
|
6351
HOLZMA HINGE INSERTER |
N/A |
|
6477
BOLSTER PLATES |
|
|
6598
#18 LANDIS ABRASIVE FACE/KNEE GRINDER, POWER TABLE, CP&T, 14” X21’ CHUCK, 15 HP, (6598) |
18 |
|
6323
HESSEMAN PROFILE SANDER |
N/A |
|
6325
SHIMURA MODEL SR-100W-PT PROFILE EDGE SANDER |
N/A |
|
6326
TORIT CASE GOODS DOWN DRAFT TABLE W/ CARTRIDGE FILTER SYSTEM & ADJUSTABLE TABLE
|
N/A |
|
6328
KUPER FW-1200 ZIG ZAG VENEER STITCHER |
N/A |
|
6893
#5H-20 GAUER, 24-11 GA , 5/8”-20” WIDE,100 FPM, 1983 (6893) |
5H-20 |
1983 |
6904
UNIFIED INDUSTRIES 1000 LB RAIL MOUNTED GRIPPER WITH 450 LB CAPACITY(6904) |
|
|
7170
#5H-20 GAUER, 24-11 GA , 5/8”-20” WIDE,100 FPM, 1966 (7170) |
5H-20 |
1966 |
7215
18” x 18” x .060” DALLAS #D200-18X18, 9 ROLL PULL THRU STR, ADJ CAB, 2002 (7215) |
D200-18X18 |
2002 |
5788
4.8” X .040 “ BRUDERER #10120B PRECISION STR, 19 ROLLS, BACKED UP, 1977 (5788) |
10120B |
1977 |
6775
SINGLE SPINDLE WALKER TURNER DRILL PRESS (6775) |
N/A |
|
6776
ARO SELF FEED DRILL (6776) |
N/A |
|
6768
NICHOLS PRODUCTION MILL, 10” X 36” TABLE, 40 TAPER, 3 HP, 4”-16” BTW SPNDLES, 20” TABLE TRAVEL, 1980 (6768) |
N/A |
1980 |
7030
2,000 LB FAIRBANKS-MORSE PLATFORM SCALE, 48” X 48” DIAMOND PLATE PLATFORM, 1,200 LB. BALANCE BAR, 12” HEIGHT |
PA3 |
1974 |
7498
#3 MOORE JIG GRINDER, 40000 RPM HEAD, DRO, 1969 (7498) |
#3 |
1969 |
7569
3000 LB. HANSFORD #1020, 24” X 44 1/2” BED, 20” STR, 28” DL, 20 TON TRYOUT, (7569) |
1020 |
1975 |
6100
3” MODERN MODEL 3A TUBE CUTOFF, 1/4” - 3”, 216 - 648 RPM, FRONT AND REAR CROSS SLIDES, COOLANT, STOCK STOP, LOW$$ |
3A |
1952 |
7593
4.33 WOTAN RAPID-O, 31.5” X 31.5 ROTARY, 49.2”X; 40.2”Y; 32.2”Z; 5 AXIS, GE2000 CNC, 1987 (7593) |
RAPID-O |
1986 |
7026
7” x .125” IRON BAY #MP12 COIL END WELDER, SQUARE ELEC TIG 175 |
MP12 |
1999 |
7730
PANGBORN ROTOBLAST, (8) 40 HP HEADS, BLAST COMPARTMENT 5’ x 19’ x 6’ H, A/B CONTROLS, 1999 (7730) |
N/A |
1999 |
7816
MEDINA MODEL B END GRINDER, (7816) |
B |
1987 |
7806
2-20, KENT-OWENS, RISE & FALL, 12" x 42" TABLE., 20" TRAVEL, 5 HP, 1975 (7806) |
2-20 |
1975 |
7845
SPEEDFAM 625TFG, 6” x 36” CHUCK, 1979 (7845) |
625TFG |
1976 |
7852
51” TANNEWITZ #SI VERTICAL SAW, WOOD |
S1 |
1964 |
7895
SWISHER AUTOMATIC MARK 6, VERTICAL SPINDLE, COOLANT, 1995 (7895) |
MARK VI |
1995 |
7713
MARKLIFT #41KBDF, DUAL FUEL, TELESCOPING ARM MAN LIFT, 41 FOOT REACH (7713) |
41KBDF |
|
7887
BARRETT MODEL 225 CENTRIFUGAL CHIP SEPARATOR, (7887) |
225 |
|
7884
BARRETT MODEL 225 CENTRIFUGAL CHIP SEPARATOR (7884)
|
225 |
|
6938
1-14 KENT OWENS PRODUCTION MILL, RISE & FALL, 9” x 32” TABLE, 1973 |
1-14 |
1973 |
7937
NORDSON POWDER PAINT SYSTEM WITH WASHER, DRYER, PAINT ROOM, CURE OVEN, IN PLANT, UNDER POWER, NEW 2000 (7937) |
|
2000 |
7917
60 KVA TAYLOR WINFIELD TYPE LIMF-25-60, ALLEN BRADLEY 600, MIYANCHI 15-120 INVERTER POWER SUPPLY, NEW (7917) |
LIMF-25-60 |
2005 |
7969
#2 BOYAR SCHULTZ DUAL SPD, UPPER AND LOWER OSCILLATING, 18” X20” TABLE (7969) |
#2 |
|
7983
#007983 (2) CINCINNATI SHEAR BLADES 102 1/4”L X 2 7/8”W X 7/8” THICK* |
|
|
7984
#007984 (2) CINCINNATI SHEAR BLADES 125 7/8”L X 2 7/8”W X 7/8” THICK* |
|
|
7986
#007986 (2) CINCINNATI SHEAR BLADES 76”L X 2 7/8”W X 7/8”THICK* |
|
|
7987
#007987 CINCINNATI SHEAR BLADES 102”L X 2 7/8”W X 7/8”THICK* |
|
|
7988
#007988 (2) CINCINNATI SHEAR BLADES 125 7/8”L X 2 7/8”W X 7/8”THICK* |
|
|
7989
#007989 (3) CINCINNATI SHEAR BLADES 54”L X 2 7/8”W X 7/8”THICK* |
|
|
7990
#007990 (2) CINCINNATI SHEAR BLADES 54”L X 2 7/8’W X 7/8”THICK* |
|
|
7991
#00791 (2) CINCINNATI SHEAR BLADES 54”L X 2 7/8”W X 7/8”THICK* |
|
|
7992
#007992 (2) CINCINNATI SHEAR BLADES 52”L X 2 7/8”W X 7/8”THICK* |
|
|
7961
1/2” MILWAUKEE MAGNETIC DRILL, 8” STROKE (7961) |
N/A |
|
7957
10” x 50” ACER MODEL 3VK, X AXIS PF, PDB, 2 AXIS DRO, VISE, 1992 (7957) |
3VK |
1992 |
8172
20,000 # CAP SOUTHWORTH UPENDER, 72” X 54” PLATFORM, HYD POWERED MECH TILT (8172) |
|
|
6840
12” x 20” TOYODA #GP15-50 PLAIN, OD, 16” WHEEL, PLUNGE, CLNT W/ MAG SEP, 1971 (6840) |
GP1550 |
1971 |
8174
#2 BOYAR SCHULTZ DUAL SPINDLE PROFILE GRINDER |
N/A |
|
8129
RAPCO #PAR6030R, 60 KVA, 30” THR, WELDTRONICS CONTROLS (8129) |
par6030 |
|
8039
16 SPD NATCO G-19, 1 1/2” UPPERS, 15” x 24” DRILL AREA, DRILL AND TAP, 1980 (8039) |
G19 |
1980 |
8131
1 SPD ALLEN # 2 1/2 MAT, 30” SWING, 150-1800 RPM, 25” X 34” TABLE, TAPPING, HF, BACK GEARED |
2 1/2 |
|
8132
1 SPD ALLEN # 2 1/2 MAT, 30” SWING, 150-1800 RPM, 25” X 34” TABLE, TAPPING, HF, BACK GEARED |
2 1/2 |
|
8133
1 SPD ALLEN # 2 1/2 MAT, 30” SWING, 150-1800 RPM, 25” X 34” TABLE, TAPPING, HF, BACK GEARED |
2 1/2 |
|
8220
METHODS MODEL SLANT 50 2-AXIS CNC LATHE 20" SWING, 40" C-C, 10" CHUCK, 3,000 RPM, 20HP, 10 POS. TURRET, YASNAC LX-3, TOOLING, 1994 (8220) |
SLANT 50 |
1994 |
8221
METHODS MODEL SLANT 50 2-AXIS CNC LATHE 20" SWING, 40" C-C, COLLET CHUCK, 3,000 RPM, 20HP, 10 POS. TURRET, YASNAC LX-3, TOOLING, 12' BAR FEED, 1995 (8221) |
SLANT 50 |
1995 |
8222
2 1/8" MODERN #2LD, 2 SLIDE, 20' MAG FEED |
2LD |
|
7655
MOLINE #13 25 SPINDLE DRILL, 10 HP, Allen Bradley DTAM+ control, (7655) |
13 |
|
8246
PINES MODEL 700 END FINISHING MACHINE, 3" CAPACITY, HYDRAULIC CLAMP, HYDRAULIC FEED, 960 - 1990 RPM, 3 1/4" DIAMETER CUTTER (8246) |
700 |
1959 |
8213
MAGNAFLUX MODEL SB-1416 DEMAGNETIZER* (8213) |
SB-1416 |
|
8052
175-MPC, SCHMIDT, HYD 7 TON, 10" DIE SPACE, 18" BH, 5 HP, 1990's |
175 |
|
8201
1-TON YALE MODEL KEL1-1STH1551 1-TON ELECTRIC CHAIN HOIST |
KEL1-1STH1551 |
|
6729
6" WIDE WADDINGTON MODEL PRF ELECTRONIC PRESS ROLL FEEDER, 1994
(6729) |
prf |
1994 |
7629
18” x 48” JAYBIRD AIR FEED (7629) |
DJ15 4818 |
|
8149
JOY “TWIST AIR” MODEL 290 AIR COMPRESSOR, 40 HP, (8149) |
290 TWIST AIR |
|
8302
STEFANI MAJOR PANEL SIZING SAWS (2) |
SQUADRATIRCDE |
2000 |
8349
12 CUBIC FT ROSEMONT RF-14-12, 13" DEEP, INT SEP, GOOD LINER, 1993 (8349) |
RF-14-12 |
1993 |
8344
60" x 120" x 60" TARUS, SWIVEL HEAD, 75 HP, 3000 RPM, 400 IPM RAPID, FIDIA C-110 CNC in 2005, 1995 (8344) |
RMXH6012 |
1995 |
8341
2" x 84" TARUS TPTCGD4085S DRILL, 3400 RPM MAIN, 2000 RPM AUX, 15 HP, 1994, CNC UPDATED 2007 (8341) |
TPTCGD408S |
1994 |
8369
MOORE G18 JIG GRINDER 1978 (8369) |
G18 |
1978 |
8337
STANLEY VIDMAR STORAGE CABINET |
|
|
8362
6' x 17" POLAMCO #WR 50/2, 30-1500 RPM, 5 MT, PWR CLAMP & ELEV, 1974 (8362) |
|
1974 |
8385
7" MODERN 6MNC, FANUC 18T, 20' MAG FEED, REAR SLIDE, FRONT TURRET, 1997 (8385) |
6MMC |
|
8389
1,000# LITTELL #10 MOTORIZED SINGLE END UNCOILER, 13" WIDTH, 12"-21" ID, 50" OD, 1/2 HP, KEEPERS, LOOP CONTROL (8389) |
10 |
|
8399
1-14 KENT OWENS HORIZ. PRODUCTION MILL, 1 HP, 9" x 32" TABLE, BREAK-A-BEAM PALM BUTTONS, ARBOR, 1970 (8399) |
1-14 |
|
8417
17 TON DIACRO #14-48-2, HYDRA-MECH BRAKE, 48” OA BED, 36” B/T , TWO SPEED, MAN. BG, 1980 (8417) |
14-48-2 |
|
8447
SUNNEN MODEL MBB-1802 HORIZONTAL HONE, POWER STROKE, AUTO SIZE, STONE SAVER, .060” - 6 1/2” ID RANGE, 200 - 2500 RPM (8447) |
MBC-1802 |
1984 |
8464
10" x 50" SWI TRAK DPM, 3-AXIS, BED TYPE, 31" x 17" x 23.5" TRAVELS, PROTOTRAK A.G.E. 3 CTRLS, 1999 |
|
1999 |
8470
6" x 126" REFORM #AR31 TYPE 5 KNIFE GRINDER, 10 HP, 1985 (8470) |
AR31 |
|
8503
#1 PINES HORIZONTAL TUBE BENDER, MANDREL EXTRACTOR, 1968 (8503) |
1LH |
|
8510
4 5/8” DAKE MEP COBRA 350 CNC FE, NON-FERROUS, PROG. FEED LENGTH, 1998 (8510 |
350 CNC FE |
1997 |
8522
#3CSM KEARNEY & TRECKER HORIZONTAL MILLING MACHINE (8522) |
3CSM |
|
8523
#3 KEARNEY & TRECKER VERTICAL MILLING MACHINE (8523) |
#3 |
|
8524
#2CSM KEARNEY & TRECKER VERTICAL MILLING MACHINE (8524) |
2CSM |
|
8525
#4CK KEARNEY & TRECKER HORIZONTAL MILLING MACHINE, 80" x 17" TABLE, 42" TRAVEL, 1500 RPM, 25 HP, 50 TAPER, ARBOR SUPPORT (8525) |
4CK |
|
8526
#205S-12 KEARNEY & TRECKER HORIZONTAL MILLING MACHINE, 56" x 12" TABLE, 25-2000 RPM, 5 HP, 50 TAPER, ABOR SUPPORT, COOLANT, (8526) |
205S-12 |
|
8527
#315TF-16 KEARNEY & TRECKER HORIZONTAL MILLING MACHINE, 68" x 15 3/4" TABLE, 34" TRAVEL, 15 HP, AUTO CYCLE, ARBOR SUPPORT (8527) |
TF315 |
|
7809
1 1/2" DIACRO #6 HORIZ HYDRAULIC BENDER, 3 HP, (7809) |
#6 |
|
8381
10.6" x 23.6" YAM #GU27-60H UNIV, COOLANT (8381) |
GU27-60H |
|
8178
4 3/4” MODERN 4KD, 5’ RUNOUT, 1979 (8178) |
4-KD |
1979 |
8476
10,000# x 36" W x .125" CWP #36D7CSF CRADLE STRAIGHTENER SERVO FEED, 1994, NEVER PUT INTO PRODUCTION |
36D7CSF |
1996 |
8588
22 GAGE LOCKFORMER ROLL FORMING MACHINE (8588) |
|
|
8587
16 GAGE LOCKFORMER (8587) |
|
|
8504
4 5/8" MODERN 4B TUBE CUTOFF MACHINE, MISC. COLLETS AND GUIDE TUBES |
4B |
|
8120
#18 LANDIS ABRASIVE FACE/KNEE GRINDER, 14” x 21” CHUCK, 15 HP, (8120) |
#18 |
|
8266
3 TON ABELL HOWE, 35'10" SPAN, TOP RUNNING, 6 WAY, 1976 (8266 |
|
1976 |
8637
4 1/2" MODERN #4K AUTOMATIC TUBE CUTOFF, 2 SLIDE, MISC. TOOLING, RBLT 2002 (8637) |
4K |
1976 |
8646
30" BULLARD CUTMASTER 5-POS TURRET, SIDE HEAD, 4 - 300 RPM, 3-JAW CH. 30 HP, 34"/44" SWING 1952 (8646) |
30" CUTMASTER |
1952 |
8666
8,000 LB HANSFORD #1030, 80" x 49" BED, POWER ROTATION & ELEVATION, 1976 (8666) |
1030 |
1976 |
8667
MAZAK QT-250 CNC LATHE, 8" CHUCK, 5,000 RPM, 20 HP, FUSION 640T CONTROL, CHIP CONVEYOR, TAIL STOCK, 2.4" BORE, 2000 (8667) |
QT250 |
2000 |
8642
10' x 14 GA. ROTO-DIE #15, FORMING & HEMMING DIES, SUPPORTS, 1982, (8642) |
15 |
1982 |
7912
LNS SUPER HYDRO BAR FEED #HYS 6.35, HS 4.8, 1993 (7912) |
N/A |
1993 |
8697
4" x .196" ROUNDO # PMV-100/5 RING ROLLER, 1999, (8697) |
PMV-100/5 |
1999 |
8726
3.94" NOMURA #B-100LP, 1200 RPM, #50, 55" X 40" TABLE, 50" VERT, 15 HP, 1978 (8726) |
B-100LP |
1978 |
8721
8,000 LB CLARK #C500-S80, 2 STAGE MAST, SIDE SHIFT, LP, (8721) |
C500-S80 |
|
8717
2,000 DEGREE GRIEVE #BF-122412 HEAT TREATING FURNACE, 2 CU/FT, 1997 |
BF-122412 |
1997 |
8687
HAMMOND #5-ROH DOUBLE END BUFFER, 5 HP (8687) |
5-roh |
|
8734
8' x 12 GA. ROPER WHITNEY #812A FINGER BRAKE, 1992 |
|
1992 |
8760
100 TON MINSTER P2-100-48-31, 4" STR, 4" ADJ, 0-250 SPM, 20" SH, 16" WINDOWS, 1996 (8760) |
P2-100-48 |
1996 |
8740
WESTERN "ARCTRONICS" 50KVA SPOT WELDER (8740) |
50 |
|
8411
1 1/2" DIACRO #8 HORIZ HYDRAULIC BENDER, 3 HP (8411) |
8 |
1974 |
8730
20" CLAUSING #2277 SGL SPNDL, VARI SPD, 150-2000 RPM, 3 MT, 22" x 19" TBL, 1-1/2 HP, (8730) |
2277 |
|
8743
10" x 50" ACER MODEL 3VK , X-AXIS PF, PDB, 2 AXIS DRO, 3 HP, 1993 (8743) |
3VK |
1993 |
8361
METHODS #400S MANUAL EDM HOLE DRILL, 16" x 16" x 16" TRAV, 50 AMP, DRO, 2005 (8361) |
400S |
2005 |
8781
4' x 12 GA. WYSONG #448 INITIAL PINCH, 4-1/4" DIA. ROLLS, 1-1/2 HP (8781) |
448 |
|
76910
60 TON BRUDERER #BSTA 60HL, ADJ STR, V/S, 800 SPM, 30" x 24.5" BED, BRUDERER FEED, 1993, (76910) |
bsta60hl |
1993 |
8796
T-DRILL #TCC45-EF, UNCOILER, STRAIGHTENER, CUTOFF, END FORMER, 1995 (8796) |
TCC-45 EF |
1995 |
8724
2'6" x 6" JOHANSON RADIAL DRILL, 105-1200 RPM, #4MT, 20" x 40" TABLE, COOLANT, 2HP, TAPPING, PF, (8724) |
|
|
8767
LUCIFER #RD8-KHE24, DUAL CHAMBER, 12"H x 14"W x 24"L, 2200 & 1200 F, 2005 (8767) |
RD8-KHE24 |
2005 |
6763
COVEL #12 TOOL & CUTTER GRINDER, 18" TRAVEL, 3,200 RPM, 3/4 HP, (6763) |
12 |
|
8813
12' x 29/64" BERTSCH #11, 13 1/2" ROLLS, INITIAL PINCH, AIR DROP, POWER ROLL ADJ, (8813) |
11 |
1967 |
8817
72" x 48" x 70" CMI-EFCO BATCH FURNACE, 1715 DEGREES F., ELECTRIC, BARBER COLEMAN CONTROLS, 1984 (8817) |
|
1984 |
8818
36" X 48" X 32" HIGH BEAVERMATIC SHUTTLE BATCH FURNACE, 2100 DEGREES F., ELECTRIC, BARBER COLEMAN 570, 1990 (8818) |
36W48L32H |
1990 |
8809
10,000# WEST BEND UPENDER, 60" x 60" PLATEN AREA, 1994, (8809) |
|
1994 |
8833
125 HP QUINCY MODEL QMA -125 ROTARY SCREW, 115 MAX PSIG, 595 CFM, 1990 (8833) |
QMA-125 |
|
8810
4.33" KALAMAZOO #FA350A COLD SAW, NON-FERROUS, 14" BLADE, 5 HP, MITER 2006 (8810) |
FA350A |
2006 |
8804
4' x 11", CARLTON, 80-2000 RPM, 4 M.T., POWER ELEVATION & CLAMPING, UNIV BOX TABLE (8804) |
|
|
6773
1 SPDL BUFFALO #18 DRILL PRESS, 18" SWG, 1 HP, #2 MT, (6773) |
18 |
1959 |
8844
TREE JOURNEYMAN 250 3 AXIS CNC MILL, 26" X, 14" Y, 5.91" Z, 4,000 RPM, TPC-2100 CTRLS, 1995 (8844) |
250 |
1995 |
8671
STONEGATE 12 STATION C-FRAME PUNCH LINE, (5) 20 TON, (7) 10 TON, 10 HP HYD. UNIT, 2000 |
|
2000 |
8451
HAMMONDV #5-VRRO, DOUBLE END, (2) 5 HP MOTORS, VS 1,500 - 3,000 RPM (8451) |
|
|
8855
SUNNEN #1803, POWER STROKE, AUTO CYCLE, STONE SAVER, 6" STR., 1991 (8855) |
1803 |
1991 |
8851
12" x 24" OKAMOTO #ACC-1224ST HYD, OWD, CHUCK & CONTROL, 1998 (8851) |
ACC-1224ST |
1998 |
8850
1" CROWN #PATRIOT RDB-10NM CNC, 3 STACK, PC BASED CONTROL, 2002 (8850) |
PATRIOT RDB-10NM |
|
8847
.079'' - 1.024'' LNS #HYDROBAR EXPRESS 226, 12' BAR LENGTH, 1999 |
EXPRESS 226 |
1999 |
8860
5 1/16" DAKE #OMP EUROMATIC 370PP COLD SAW, FERROUS, AUTO, 14 1/2" BLADE, 1999 (8860) |
370A/P.P. |
1999 |
8861
OKUMA CROWN, 762S-BB, OSP-U10L CNC, 10"CK, TS, 12 POS TURRET, LOW HOURS, 1997 (8861) |
CROWN 762S-BB |
|
8862
12" x 24" KENT #KGS-306AHD, IDF, CHUCK & CONTROL, CP&T, OWD, 1988 (8862) |
KGS-306AHD |
|
8611
HURRICANE #5024 BELT WASHER, 24” W, ELECT HEAT, SKIMMER, CART WITH WHEELS, 1991 (8611) |
5024 |
1992 |
8484
#2 HFR MITTS & MERRILL, 1 1/4" WIDTH x 12" LENGTH, 2 3/8" POST, (NO PIT REQUIRED) (8484) |
#2 |
1970 |
8854
16" HEALD MODEL 261-16 ROTARY, 16" CHUCK, 14" WHEEL (8854) |
261 |
|
8853
16" HEALD MODEL 261-16 ROTARY, 16" CHUCK, 14" WHEEL (8853) |
261 |
1956 |
8837
10" x 12" NELMOR GRANULATOR, 7 1/2 HP, 1995 (8837) |
G1012 |
1995 |
8838
8" x 10" NELMOR GRANULATOR, 5 HP, 1994 (8838) |
810 |
1994 |
8871
40" x .080" HERR VOSS #VMLD48/1.75-17/5, 4-HI, RH, 1995 (8871) |
VMLD4811.75-175.4HIRH |
1995 |
8869
18" x 22" MARVEL #8 MK II, 1" BLADE, COOLANT, POWER FEED 1991(8869) |
SERIES 8 MKII |
1990 |
8874
34" x 14" x 6" HURCO H5SSM, 5 HP, 3800 RPM, 3-AXIS ULTIMAX SSM CNC, 42" x 13" TABLE, 1997 (8874) |
H5SM |
1997 |
7985
#007985 (2) CINCINNATI SHEAR BLADES 125 7/8”L X 2 7/8”W X 7/8” THICK* |
|
|
7719
6” WHITE/SUNDSTRAND BELT GRINDER |
N/A |
|
8890
7" x 91" JOHNSON-REYNOLDS DOUBLE END, HYD CLAMPING, 20 HP (8890) |
|
|
8887
7.5 TON AUTO SERT AS-7.5, 6" STROKE, 20" THROAT, FEEDER BOWL, INSERTION PRESS, 1999 (8887) |
AS-7.5 |
|
8806
24" x 24" CENTRI-SPRAY #MCCS1500, WASH, BLOW OFF, 2001 (8806) |
MCCS1500 |
2001 |
8926
25.59” x 15.75” x 15.75” MAKINO #MAX 65SA20, 12,000 RPM, 20 ATC, 4400 HOURS 1200 IPM, 2001 (8926) |
MAX65S A20 |
2001 |
8911
20,000# COIL PRO UPENDER, 60" x 61" PLATFORM, 60" x 43" V-DECK, DOUBLE CHAIN DRIVE, 3 HP, 1999 (8911) |
|
1999 |
8917
8 TON PEMSERTER MODEL 2000A HYD, BOWL FEED, TOUCH SCREEN PLC, 2000 (8917) |
2000A |
2000 |
8921
8 7/8" BOSCHERT #PN4 NOTCHER, 1/4" CAP, 1985, (8921) |
PN4 |
1985 |
8918
12" SCOTCHMAN #315NF/HFA, NON FERROUS, AUTO, 3.5" TUBE CAP., 2" SOLIDS, 1998, (8918) |
315NF/HFA |
1998 |
8934
CYCLONE #4824 TOP AND SIDE DOOR OPENING BLAST CABINET (8934) |
4824 |
|
8815
3.94" SHIBAURA #BT-10B(R1) HBM, 44" x 49" ROTARY TBL, 50 TAPER, 1,000 RPM, 1981 (8815) |
BT-10B(R1) |
1981 |
8922
1 1/4" DIACRO #6 HORIZ HYD BENDER, 5/8” SOLID BAR, 3 HP, (8922) |
#6 |
|
8910
SUNNEN #CV616 “CYLINDER KING” VERTICAL HONE, 8” DIA. x 9” LENGHT, TONS OF TOOLING, 1992, (8910) |
CV616 |
1992 |
8894
6' x 12 GA DREIS & KRUMP BOX AND PAN BRAKE WITH FINGERS, 1989 (8894) |
BPO-612-6 |
1989 |
3136
NO. 2EF73 CINCINNATI HEALD, 16” STROKE, ELECTRO-STATIC WAYS, 1974 |
2EF73 |
1975 |
4859
.050" TO 2" DIAMETER BRYANT CENTERHOLE , 2" TO 42" CAP, DRESSER, 1970 |
|
1970 |
4963
ELOX ASTRA MKII 200D DUAL SOLID STATE DIGITAL EDM POWER SUPPLY, 200 AM |
ASTRA MKII 200D |
|
4591
24” AVEY #2-BMA-6, SINGLE SPD, PF, TAP, 150-1800 RPM, #3MT, 2 HP |
#2-BMA-6 |
1951 |
4634
24” AVEY #2-BMA-6, SINGLE SPD, PF, TAP, 150-1800 RPM, #3MT, 2 HP |
#2-BMA-6 |
1951 |
5330
ELTEE #TR20 PULSITRON EDM, POWER SUPPLY, 1984 |
TR20 |
1984 |
7081
1 1/4” PINES MODEL 1400, HAND CLAMPING (7081) |
1400 |
1977 |
6970
1 3/8” PINES #3/4 HOR, HYD MANDREL EXTR, 6 STATION TURRET DEPTH STOP, 1989 (6970) |
#3/4 |
1989 |
4693
L-G SGL SPDL 26" DRILL, 5” QUILL TRAV, 25” X 26” TABLE, HAND FEED, BG, 150 TO 1800 RPM (4693 |
2LMS |
|
7918
1 SPD ALLEN, 30” SWING, 150-1800 RPM, 25” X 34” TABLE, TAPPING, POWER FEED, BACK GEARED (7918) |
MADWT |
1987 |
7959
24” CYCLEMATIC DRILL PRESS, #4MT, 2 SPEED 3/4 & 1 1/2HP, TAP |
N/A |
|
8492
1 SPINDLE SOUTH BEND IBARMIA #B-50P, BOX COL, POWER ELEV, POWER FEED, LATE MODEL, 8492) |
B-50-P |
|
8449
1 3/4" PINES #1, MANDREL EXTRACTOR, 1 1/2” x .109” WALL, 8 POS TURRET, TOOLING, 1991 (8449) |
#1 |
1991 |
8502
1 1/2" PINES #1 HORIZONTAL TUBE BENDER, DEGREE OF BEND SELECTOR, 1979 (8502) |
#1 |
1979 |
8925
1 1/4" DIACRO #6 HORIZ HYD BENDER, 5/8” SOLID BAR, 3 HP, 1980, (8925) |
#6 |
1980 |
5283
BARNESDRILL MODEL 122, 3HP, 12" TRAVEL 200-900 RPM, CLNT, 1967 |
122 |
1967 |
5491
#205-SA K & T, 12” X 50” TABLE, 28” LONG TRAV, 1500 RPM, 5 HP, 1 HP VERT HEAD, 1964 |
205-SA |
1964 |
7330
MOORE #2 JIG GRINDER, 40,000 RPM SPINDLE, 2 AXIS DRO, 10” x 19” TABLE, (7330) |
2 |
1953 |
7747
3 1/2" PINES #2 HOR, CCW, DIAL A BEND, TOOLING, 1974 (7747) |
#2 |
1974 |
3981
1 1/4" PINES #3T VERTICAL HYD, 20 HP, DEGREE OF BEND, PALM BT, 1973 |
3T |
1973 |
5651
3’ x 8” KAO MING#700S RADIAL DRILL, 1500 RPM, 2 HP, #4 MT, POWER ELEV., 1978 |
700S |
1978 |
6683
1 1/4" PINES #3T VERTICAL, 20 HP, 10 DEGREE OF BEND, 1980 (6683) |
3T |
1980 |
6682
1 1/4" PINES #3T VERTICAL, 20 HP, 10 DEGREE OF BEND, 1979 (6682) |
3T |
1979 |
6704
1 1/4" PINES #3T VERTICAL, 15 HP, 10 DEGREE OF BEND, 1960 (6704) |
3T |
1960 |
7419
1 1/4" PINES #3T VERT, DIGITAL DIAL A BEND CONTROL, 20 HP, PALM BUTTONS, 1984, UPDATED CONTROL (7419) |
3T |
1984 |
8741
3' x 9" CINCINNATI-BICKFORD,175 - 1500 RPM, #4MT MONO-ARM, COOLANT (8741) |
|
1951 |
8916
3' x 10" IKEDA #RM-1000, 30 - 1440 RPM, 5 HP, BOX TABLE, 1977 (8916) |
RM-1000 |
1977 |
8943
3.94" NOMURA B100WP, 96" X 48" TABLE, 96" x 43" x 60" TRAVELS, 50 TAPER, 21 - 1200 RPM, 3-AXIS DRO, TELESCOPING COVERS (8943) |
B100WP |
1981 |
8944
3.94" NOMURA #B100WP, 96" x 48" TABLE, 96" x 43" x 60" TRAVELS, 50 TAPER, 21 - 1200 RPM, 3-AXIS DRO, TELESCOPING COVERS (8944) |
B100WP |
1980 |
6873
4” x .062” COILMATE / DICKERMAN SMT4 SERVO, 999.999” LENGTH, PRESSMOUNT BRACKET, 2002 (6873) |
SMT4 |
2002 |
8115
4’ x 15” YMZ (TOMINAGA) #RH1500 RADIAL DRILL, 33 - 2010 RPM, #5MT, 1990 (8115) |
RH1500 |
1990 |
8413
4’ x 13” IKEDA RADIAL DRILL, RM-1300, 13-1440 RPM, #5 MT, TILTING BOX TABLE, COOLANT, 7 1/2 HP, 1978 (8413) |
RM-1300 |
1978 |
8386
4" GIDDINGS & LEWIS 340T, 98" X 48" TABLE, 60" VERT, 1300 RPM, 1956 (8386) |
340-T |
1956 |
8591
4' x 11" CARLTON #1A RADIAL DRILL,60 - 1500 RPM, PWR ELEV & CLMP, 5 HP, BOX TBL, 1951 (8591) |
|
1951 |
8569
16" BROGANTECH (JOSEPH MCH CO), NON-FERROUS, 4" CAP, 3 HP, 20' AUTO INFEED, CNC, 1997 (8569) |
|
1997 |
8581
24" SAVAGE #RS-1020V, PWR DOWN FEED, 4" CAP, FEED TABLE, 20 HP, 1985 (8581) |
RS-1020V |
1985 |
8879
4' X 3/8" CINC #2504R MECH, 36" FOPBG, 2 FRONT SUPPORTS, SQ ARM, 1971, (8879) |
2504R |
1971 |
8906
4' x 12" OOYA #1250 RADIAL DRILL, #4MT, 38 - 1,985 RPM, PWR CLMP & ELEV, (8906) |
1250 |
|
8203
4.33" SOCO MODEL HVS-375FA-DR FERROUS COLD SAW, 14.75" BLADE, 5HP, 2005, (8203) |
HVS-375FA-DR |
2005 |
6746
4 1/2” AMROX HORIZ BAND SAW (6746) |
N/A |
2000 |
8710
4 5/8” DAKE MEP COBRA 350 CNC FE, NON-FERROUS, 14" BLADE, 4.5 HP, MITER, PROGRAMMABLE, CHIP/DUST COLLECTOR 2001 (8710) |
350CNCFE |
2001 |
7651
5” OMP # EUROMATIC 370, MATIC 315 CS-CM-2B-R COLD SAW* |
370 |
1993 |
8585
20 GA. LOCKFORMER #20 ROLLFORMER, 5 STATIONS, 1995 |
20 |
1995 |
8304
5 1/16” DAKE OMP EUROMATIC 370/PP-L AUTO FEED, MITRE, 2002 (8304) |
EUROMATIC 370PP-L |
2002 |
7100
6 TON DENISON HYD PRESS (7100) |
319 |
|
7027
6” x .040” PERFECTO # 17-6-5 FEEDER/STRAIGHTENER, 5 ROLLS, INDRAMAT DRIVE, CABINET MOUNT, 1994 (7027) |
17-6-5 |
1994 |
7763
#630TF20 K&T, 19.5” X 108” TABLE, 1500 RPM, 3 AXIS DRO, 30 HP, COOLANT, 1974 (7763) |
630-TF-20 |
1974 |
3839
6” x 6” AIR FEEDS INC. MODEL AF-2 AIR FEEDER, 8” ACTUAL WIDTH, 5-ROLL STRAIGHTENER, .156” THICK, 90 SPM, 1994( 3839) |
|
1994 |
7619
6” x 18” SUPERTEC #STG-450 UNIV CYL, DROP DOWN ID, CP&T, 1986 (7619) |
STG-450 |
1986 |
8638
6" DURANT #VS-MSC-27 STRAIGHTENER, 9 ROLLS, .100" MAX THICKNESS, VARIABLE SPEED, 1997, (8638) |
vs-msc-27 |
1997 |
8784
6" X 48" FMB PLUTON HBS, FOR PANEL/GRATING, 1 1/4" BLADE, 2.5 HP, 62-310 FPM, SEMI-AUTO, GEAR DRIVE, COOLANT, 1999 (8784) |
PLUTON |
1999 |
8790
6" x .125" VAMCO #CFS-6-II SERVO FEED, NEW 2000 (8790) |
CFS-6 II |
2000 |
7247
#MBC-1804 SUNNEN, POWER STROKE, AUTO CYCLE, STONE SAVER, 060”-6.5” DIA, 16” LENGTH, 6” STR, TOOLING, 1988 (7247) |
1804 |
1988 |
8878
MBC-1804 SUNNEN, POWER STROKE, AUTO CYCLE, AUTO SIZE, STONE SAVER, .060”-6.5” DIA, 16” LENGTH, 6” STR, TOOLING, 1990 (8878) |
1804 |
1990 |
6014
8 TON DENISON MODEL WSO8 HYD PRESS, 12” STR, 18” DL, 21” x 13” BA, 1977 (6014) |
WS08 |
1977 |
7812
8 TON DENISON, 22” STR, 36” DL, 18”X 15”, 1990 (7812) |
WR87M |
1990 |
7978
8-TON DENISON MODEL WR-85, 12” STROKE, 16” DAYLIGHT, 7 1/2” THROAT, 615 IPM ADVANCE, 5 HP, PALM BUTTONS, 1985 (7978) |
WR-85 |
1985 |
7979
8 TON DENISON #FF8C, UPDATED ELECTRICS 1954 (7979) |
FF8C02 |
1954 |
8185
8 TON DENISON #WR87M, 12" STR, 16" DL, PALMS, (8185) |
WR87M |
|
8403
8 TON DENISON WR SERIES, 12" STR, 16" DL, 6-POS ROTARY TABLE, 415 IPM, PALM BUTTONS, 7 1/2 HP, 1992 (8403) |
WR4R87MC409SS1 |
1992 |
8727
8' x 19" CARLTON 4A, 1200 RPM, PRESELECT HEAD, 25 HP, 1965 (8727) |
|
1964 |
8756
SUNNEN #CK-21E "CYLINDER KING" VERTICAL, MICRO PROCESSOR CONTROL, ASST TLNG, 1997 (8756) |
CK-21 |
1997 |
8807
26" SAVAGE #481 ABRASIVE CUT-OFF SAW, 8" CAP, OSC.,40 HP, 1983 (8807) |
481 |
1983 |
8173
9 STAND DAHLSTROM, 2” ARBORS, 30” ROLL SPACE, 24” HOR CC, 4” VERT ADJ, (8173) |
|
|
8450
9 STATION TRIPLEX LOCKFORMER CLEATFORMER, 20 to 28 GA., 1989 (8450) |
TRIPLEX |
1989 |
4985
10 TON BAIRD MODEL #2 GAP , 2" STR, 7" SH, 13.5" x 7.75"BA, 0-300 SPM, 1973 |
#2 |
1973 |
7907
36” DOALL #V36 VERTICAL, V/S, WELD AND GRINDER, |
V36 |
1964 |
7928
10.24” X 10.24” KASTO #SSB260VA AUTOMATIC VERTICAL SAW, AUTO STOCK FEED, CHIP CONV, 1988 (7928) |
SSB260VA |
1988 |
8060
10 TON LOGAN #6100 C-FRAME, 16” STROKE, 22” OPEN DAYLIGHT, 6” CLOSED, 5 HP (8060) |
6100 |
1963 |
8402
10 TON GREENERD HPB-10 , 6-STATION ROTARY TABLE, 8" STR, 10" DL, 418 IPM, 5 HP, 1994 (8402) |
HPB-10 |
1994 |
8359
10" x 14" WF WELLS W-10-2A, 2 POST, AUTOMATIC, 1" BLADE, MULTI-STR, 1997 (8359) |
W-10-2A |
1997 |
8576
10 CUBIC FT VIBRA-FINISH #VF-10, BOWL TYPE, URETHANE, SEPARATOR, 10 HP, 1991 (8576) |
VF-10 |
1991 |
8431
10 1/4" x 12" DAITO GA260W, AUTOMATIC, 1 1/4" BLADE, AUTOMATIC, 1987, (8431) |
GA260W |
1987 |
8764
9” x 16” DOALL #C-916SA , MITRE CAPABILITY, DUAL VICES, 2 HP, 1” BLADE, 1995 (8764) |
C-916SA |
1995 |
8800
10" DAKE/JOHNSON #JH10 HORIZ, UP TO 1" BLADE, 1990 |
JH10 |
1990 |
8905
10" x 30" HARRISON #AA LATHE (8905) |
AA |
|
8901
11.8" x 10.2" BEHRINGER #HPB263A TWIN COLUMN AUTO, 1 1/4" BLADE, 5.4 HP,1995 (8901) |
HBP263A |
1995 |
5672
36” DOALL #3612-2H, 0 - 5200 FPM, 30 1/2” X 40 1/2” TBL, WELDER/GRINDER, 1981 |
3612-2H |
1981 |
5667
12 TON DENISON #WS127 GAP, 12” ST, 16” DL, 1973 |
WS12 |
1973 |
7342
PERFECTO MODEL 17-12-9 POWERED STRAIGHTENER, 12” W, 9 ROLLS |
17-12-9 |
1992 |
7340
12” FEED LEASE #FLPS-1-3/4-12-11 STRAIGHTENER, 11 ROLLS |
FLPS-1-3/4-12-11 |
1999 |
7673
12” X .125” LITTELL 412-7PDL, 7 ROLL, MANUAL ENTRY PINCH, V/S, 1979 (7673) |
412-7PDL |
1979 |
7701
12” X .018” TO .125” LITTELL 412-7R, MANUAL ENTRY PINCH, VS, 1986 (7701) |
412-7PDL |
1986 |
7703
12” WIDE X .125” X 18” STROKE DALLAS D200, ADJ CABINET BASE, (7703) |
D200 |
1986 |
7704
12 TON DENSION #WS1215M, 12” STR, 18” DL, 6 POS ROTARY TABLE, 15 HP, 1978 (7704) |
WS1215M |
1978 |
7860
12 TON HANNIFIN C-FRAME,, 3” STR,12” DL,15” x 10” BED, (7860) |
12 1/2 |
1950 |
7894
12 TON TRU-TECH CUT-OFF, 0 - 3” STR, 33” BETWEEN POSTS, 1995 (7894) |
N/A |
1995 |
8037
12” x 12” AIR FEEDS INC #AF3, PULL THRU STR, CABINET MOUNTED, 3” BORE, 1994 (8037) |
AF3 |
1994 |
8017
36” DOALL # 3612-2H, 1” BLADE CAP, HYD TABLE FEED, WELD & GRD, 1985 (8017) |
3612-2H |
1985 |
8028
12 TON GREENERD #HC-12-11L2, 12” STR, 24” DL, 24” x 15” BA, 5 HP, PALMS, 1980 (8028) |
HC-12-11L2 |
1980 |
7496
12" X 12" WELLSAW #1270, 12" X 12" FLAT, 12.75" RD., 60-300 FPM, 3 HP, 1975 (7496) |
1270 |
1975 |
8254
12 TON GREENERD #HCA-12-20R3, 12" STR, 18" DL, 993 IPM ADV, LIGHT CURTAINS, 1995 (8254) |
HCA-12-10R3 |
1995 |
8238
12" DOALL #C305A HORIZ, SAW, 1 1/4" BLADE, 1992, (8238) |
C305 |
1992 |
8444
6" x 12" MITSUI MODEL MSG-200MH HAND FEED SURFACE GRINDER, BEARING WAYS, ELECTRIC CHUCK, 8" WHEEL, 1 1/3 HP (8444) |
MSG-200MH |
1977 |
8445
6" x 12" MITSUI MODEL MSG-200MH HAND FEED SURFACE GRINDER, BEARING WAYS, ELECTRIC CHUCK, 8" WHEEL, 1 1/3 HP (8445) |
MSG-200MH |
1976 |
8649
12" x 12" DOALL #C-1212A, AUTO BAR FEED, 1" BLADE, 1979 (8649)) |
C-1212A |
1979 |
8693
12 TON SCHULER/LEUKART MODEL 12-OGF GAP FRAME HYDRAULIC PRESS, 20" STROKE, 22" DAYLIGHT, PALM BUTTONS, 1985 (8693) |
12-OGF |
1985 |
8704
12 TON BANTAM #B412, 50" BED, ADJ STR 0 TO 1.75", DIE HOLDER, (8704) |
B412 |
|
8722
12 TON DIACRO #16-36 HYDRA-MECH BRAKE, 3' OA, 25" BH, TOOLING, (8722) |
16-36 |
|
8747
12 STD TISHKEN #12-HMW-1-1/2, 12" RS, UNCOILER, 1997 (8747) |
12-HMW-1-1/2 |
1997 |
8841
6" X 12" HARIG MODEL 612, WALKER FINE LINE ELECTROMAG CHUCK, NEWALL DRO, HARD WAYS, WORK LIGHT, 1.5 HP, 1990 (8841) |
612 |
1990 |
8840
6" X 12" HARIG MODEL SUPER 612, WALKER FINE LINE, ACCURITE DRO, VERTICAL FINE FEED, HARD CHROME WAYS, WORK LIGHT (8840) |
SUPER 612 |
1982 |
8839
6" X 12" HARIG MODEL 612, WALKER FINE LINE, NEWALL DRO, HARD WAYS, WORK LIGHT, 1.5 HP, 1993 (8839) |
612 |
1993 |
7893
12 TON TRU-TECH CUT-OFF, 0 - 3” STR, 18” BETWEEN POSTS, 1995 (7893) |
N/A |
1995 |
8795
12" x 20" BEHRINGER #310/526G SEMI-AUTO HORIZ, 2 POST, 1.25" BLD, MITRE, 1995 (8795) |
310/523G |
1995 |
6966
60” THR X 13” TANNEWITZ MODEL 60MH VERTICAL BAND SAW* (6966) |
60MH |
1962 |
8338
36" TANNEWITZ #3600MH VERT, THRT 36", 13" VERT, 1/8"-1 1/4" BLD, (8338) |
3600MH |
|
8613
24" DAKE VH24 VERT BAND SAW, 13" WORK HGT, BLADE W&G, HYD TABLE, (8613) |
VH24 |
1996 |
4997
20" x 60" BROWN & SHARPE #4 , INTERNAL ATTACH, MAG CHUCK, CLNT 1962 |
4 |
1962 |
6769
14” XLO #14-808 COMPARATOR, SURF ILLUM |
14-808 |
1970 |
7949
14” x 40” JFMT-GWM GAP BED ENGINE LATHE, 3 AND 4 JAW CHKS, GAP (7949) |
J360A |
1992 |
8845
14" x 40" NATIONAL ENGINE LATHE, GAP BED, 2 1/8" BORE, 40 - 1800 RPM, HARD WAYS, MUCH TOOLING, 1992 (8845) |
1440 |
1992 |
7282
15 TON HANNIFIN F-150 HYD. PRESS, 16” STROKE, 22” OPEN DAYLIGHT, 10” THROAT, PALM BUTTONS, 22” X 19” BED (7282) |
F150-11M |
1964 |
7844
15 TON ROUSSELLE MODEL 15H, ADJ BED, 2” STR, 160 SPM, 1997 (7844) |
15H |
1997 |
8057
15 TON NEFF #D15-5HS, 10" STR, 18" DLO, 18" x 16" BED, 10” THROAT, 1998 (8057) |
D15-5HS |
1998 |
8056
15 TON, NEFF, FLOOR, 10" STR, 24" DLO, 22" x 21" BED, 1996 (8056) |
N/A |
1996 |
8355
15 TON METAL MECHANICS 4-POST HYD PRESS, 18" STR, 30" DL, 30" x 29" BED, 736 IPM ADVANCE, 1995 (8355) |
|
1995 |
8473
15 TON ROUSSELLE #2, 2" STR, 7 3/4" SH, 11" x 16" BA, 160 SPM VARIABLE, 1990 (8473) |
#2 |
1990 |
8915
15" x 50" COLCHESTER TRIUMPH 2000, 23" GAP, 2000 RPM, 7.5 HP, TOOLING, (8915) |
|
|
8419
16" x 40" SUMMIT GAP, 3" HOLE, TAPER, 2-AXIS DRO, 4-WAY RAPID TRAV, 25-1800 RPM, 2-SPD TS, TOOLING, 1992 (8419) |
16-3" |
1992 |
8597
#11ACD-16 BLANCHARD ROTARY, SERVO FEEDS, 15HP, 1994 (8597) |
11AD-16
|
1993 |
8852
16" x 20" HEM #1200LAR AUTO HORIZ, 1 1/4" BLADE, 5 HP, 1984 (8852) |
1200LAR |
1984 |
8856
16" x 80" ROMI #16-8;1800 RPM, 2.25" BORE, 3 & 4 JAW CK, COLLET , STEADY, 2-AXIS DRO (8856) |
16-8 |
1996 |
8903
16" x 17" W.F. WELLS F-16-2A, FULL AUTO, 1 1/4" BLADE, 2-POST, 7 1/2 HP, MULTI-STROKE, ENTRY CONVEYOR, 1993 (8903) |
F-16-2A |
1993 |
8927
16" x 16" AMADA #HFA-400W, 1 1/2" BLADE, PROG STK FEED, 8 HP, 1996, (8927) |
HFA-400W |
1996 |
8928
16" X 20" MARVEL 15A9PC, FEED TABLE, PLC, 1 1/4" BLADE, 7.5HP, 1995 (8928) |
15A9PC |
1995 |
8902
16” x 16” AMADA #HA400, 1 1/4” BLADE, AUTOFEED, 5 HP, 1981 (8902) |
HA400 |
1981 |
8889
MAZAK QT20HP, T-PLUS, 3.15" HOLE, 20" C-C, CHIP CONV. 20 HP, 4000 RPM, TOOL EYE, TS, 1996 (8889) |
QT20HP |
1997 |
5652
8” x 18” GALLMEYER & LIVINGSTON #260 HYD, INC DN FD, CLNT, 1969 |
260 |
1969 |
5785
6” x 18” PARKER-MAJESTIC #2 HAND FEED SURFACE GRINDER, 1973 |
2 |
1973 |
5055
#2 BOYAR SCHULTZ SINGLE SPINDLE , 18" x 20" TABLE, 1966 |
#2 |
1965 |
6753
6” x 18” REID, 6” x 18” PERM MAG CHUCK, 1 HP POPE DIRECT DRIVE, BIJUR AUTO LUBE, WHEEL DRESSER, GOOD COND. |
618 |
1958 |
5697
18 SPDL DEKA #HRG-1222-18, 10 HP, 9/16” UPPERS, 14-1/2” x 22-3/4”, 1979 (5697) |
HRGC-1222 |
1979 |
7290
6” X 18” BROWN & SHARPE TECHMASTER, 2 AXIS HYD, ELECT CK W/ VAR CONTROL, |
618 |
1985 |
7289
6” x 18” PARKER MAJESTIC #2Z, 5” x 10” CHK, 1 HP, POWER ELEV, 1973 (7289) |
2Z |
1973 |
7658
6” x 18” HARIG SUPER 618 GRINDER, 6” x 18” WALKER FINE LINE, FINE FEED DOWN AND CROSS, 1978 |
SUPER 618 |
1978 |
7960
6” x 18” ACER #SUPRA-618 HAND FEED SURFACE GRINDER, 6” x 18” FINE LINE CHUCK, 1992 (7960) |
SUPRA-618 |
1992 |
8252
18 TON L&J, 11/2" STR, 8 3/4" SH, 18" X 11.5" BED, 1978 (8252) |
18 |
1978 |
8657
18” x 20” MARVEL #8 MK 1, 1” BLADE, CLNT, 2 HP, VISE, 1983, (8657) |
#8 |
1983 |
8842
6" X 18" CHEVALIER FSG 618M HAND FEED SURFACE GRINDER, BALL WAYS, FINE LINE CHUCK, 2 HP, 8" WHEEL, 1998 (8842) |
FSG 618M |
1998 |
8892
18" x 80" HARRISON #M460, 3" HOLE, 3 JAW CK, DRO, 1998 (8892) |
M460 G/H |
1998 |
8938
18" x 18" MARVEL #8/M4, TILT HEAD, 3/4" BLADE, 1978, (8938) |
#8m4 |
1978 |
8884
MORI SEIKI CL-20B, 18.5" SWING, 2.8" BORE, 3500 RPM, 10HP, 8" 3-JAW, COLLET CH, YASNAC LX-3, 1995 |
CL-20B |
1995 |
8360
HARDINGE #CS-42 CONQUEST, 19 1/2" SWING, 11" X AXIS TRAVEL, 5,000 RPM, GE FANUC OT CTRL, 1988 (8360) |
CONQUEST |
1988 |
4715
20 TON MINSTER PM2-20 SS, 1.25"STR, 9.75"SH, 20" x 24"BA, 0-1000SPM, 1974 |
PM2-20 |
1974 |
5593
20 TON DENISON #GP-020 4 POST HYD PRESS, 18” ST, 30” DL, 31” X 39” BED, 1986(3) |
GP020 |
1986 |
5702
20 TON DENISON #FH20 HYD. C FRAME PRESS, 12” STR, 21” DL, 26” X 18” BED, 1978 |
FH2020HC304FSHW1CR5612 |
1979 |
5488
18” x 102” LEBLOND #1610 H.D., 20 HP, 2250 RPM, T/S FEED, 4-JAW CK, S/R, 1961 |
1610 |
1961 |
6979
20 TON SCHULER LEUKART #OGF-20, C FRAME, 18” STR, 24” DL, 36” ROTARY TABLE, DUAL PALM BUTTONS, 1983 (6979) |
OGF-20 |
1983 |
7295
32” NORTHFIELD WOODWORKING SAW, 32” x 26” TABLE, 20” VERT, 18’ 2” BLADE, TILTING TABLE, 2 HP, 7,539 FPM |
32” |
1969 |
6978
20 TON TISHKEN #AC0-20LP, 4 POST AIR TOGGLE, 21” B/T POSTS, 1 1/2” OR 2” STROKE, DIE ACCEL, 1999 (6978) |
N/A |
1999 |
7810
20 TON DENISON FH20, 12” STR, 21” DL, 26” X 17” BED, HANDWHEEL INCHING, 1978 (7810) |
FH20 |
1978 |
8256
20 TON GREENERD 4D-20-30X24-8R, 4-POST, 18" STROKE, 24" DAYLIGHT, 30" X 24" BET POSTS, HEAT EXCHANGER, 1995 (8256) |
4D-20-36X24-R3 |
1995 |
8257
20 TON GREENERD 4D-20-30X24-8R, 4-POST, 18" STROKE, 24" DAYLIGHT, 30" X 24" BET POSTS, HEAT EXCHANGER, 1995 (8257) |
4D-20-36X24-R3 |
1995 |
8328
20 TON DENISON #FH20 "MULTIPRESS" GAP FRAME, 12" STR, 21" DL, 25-3/4" x 17-1/2" BA, 1980 (8328) |
FH20 |
1980 |
8397
8" x 20" OKAMOTO #820N HYDRAULIC, IDF, 8" x 18" WALKER FINE LINE CHUCK, 1982, (8397) |
820N |
1982 |
8628
18" x 20" MARVEL #81/M5, TILT HEAD, 1-1/4" BLADE, PWR TILT, 10 HP, 1980, (8628) |
81/M5 |
1980 |
8629
18" x 20" MARVEL #81A10PC/M3MA/M4A, HYD TILT, AUTO BAR FEED, 10 HP, 1-1/4" BLADE, 1986, (8629) |
81A10PC/M3MA/M4A |
1986 |
8660
20 CU FT ROTO-FINISH #ST-20B, BOWL TYPE, SEPARATOR, TIMER, 10 HP, 1982 (8660) |
ST-20B |
1982 |
8716
8" x 20" OKAMOTO #820A, IDF, ELEC CHUCK, CLNT, DRESR, 1989, (8716) |
|
1989 |
7357
20 TON DENISON #FH20 HYD GAP, 12” STR, 21” DL, 10” THRT, 26” x 18” BED, CUSHION, PLC, 1992 (7357) |
FH-20 |
1992 |
8893
18" x 20" MARVEL #8, TILT HEAD, 3/4" BLADE, 1974, (8893) |
#8 |
1974 |
8946
8" x 20" OKAMOTO MODEL ACC820DXNCP, FANUC OM CONTROL, 8" X 1" X 1.5" WHEEL, 2 HP, COOLANT W/ FILTER, DRESSER, 1998 (8946) |
ACC820DXNCP |
1998 |
8363
19.7" x 17.7" x 17.7" NTC NV4S, TWIN ROTARY PALLETS, 12K RPM, THRU SPD CLNT, FANUC 21, 1999 (8363) |
NV4S |
1999 |
8846
OKUMA LU-300M CNC LATHE, 8" CHUCK, TWIN TURRETS, LIVE TOOLING, C-AXIS, HIGH PRESSURE COOLANT, 30HP, 2003 (8846) |
LU-300M |
2003 |
8812
MAZAK SQT 200M , 20" SWING, 21" TURNING LENGTH, 2.05" BAR CAP, LIVE TOOL, FUSION CONTROL, 2000 |
SUPER QWIK-TURN 200M |
2000 |
8888
21"/32" x 40" CLAUSING COLCHESTER #21, GAP, INCH/MM, 3.5" HIS, CHUCKS, (8888) |
|
|
4990
#2-6 BOYAR SCHULTZ SINGLE SPINDLE, 22" X 22" TABLE, 6” WHEEL, 1968 |
#2-6 |
1968 |
6457
22 TON MINSTER B1-22, 2” STR, 9” SH, 20” X 12” BED, 150-300 SPM, 1977 (6457) |
B1-22 |
1977 |
6467
22 TON BLISS # CH-22, 2 1/2” STR, 9 1/4” SH, 23 1/2” X 14” BED, 175 - 350 SPM, IMCO LOAD MONITOR, 1970 (6467) |
CH-22 |
1970 |
6471
22 TON HPC-22 FLEXO-PRESS, 1.5” STR, 275-800 SPM, AIR C/B, 18” X 14” BED, CONSOLE CNTRL,TON MTR, 1970 (6471) |
HPC-22 |
1970 |
8489
22 TON WEIDEMANN C2000, A/I, FANUC OP, HYD CL, 114 TOOLING, 1989 (8489) |
C2000 |
1989 |
8652
18" x 22" MARVEL #MV460PC/2 TILT FRAME AUTOMATIC, 1.25" BLADE, PROG CTRLS, 1999, (8652) |
MV460PC/2 |
1999 |
8676
22 TON MURATA WIEDEMANN MOTORUM 2044, 2 A/I, FANUC 18iP, 114 & MARATHON, 1999 (8676) |
2044 |
1999 |
8814
HWACHEON MODEL HI ECO 21HS-S-MC 3-AXIS CNC LATHE, 8" MAIN, 6" SUB, LIVE TOOL, C-AXIS, 20 HP, FANUC 18T, CHIP CONV., PARTS CATCHER, 1999 (8814) |
ECO21HS-S-MC |
1999 |
7595
BROTHER MODEL TC229N, 18.9” X; 14.2”Y; 10.6”Z, 10000 RPM, 14 ATC, 1996 (7595) |
TC229N |
1996 |
5237
8" x 24" BROWN & SHARPE #824 DIAL-A-SIZE, INC DN FD, HYD DRESS, ELEC CHUCK, 1983 |
824 |
1983 |
4730
24" AEM #CS-240 MDDM WET DISC GRINDER, CLNT, VARI-SPD,1987 |
CS 240 MDDM |
1987 |
4577
8" x 24" DOALL G-10 SURFACE GRINDER, COOLANT |
G-10 |
|
7587
8” x 24” GALLMEYER & LIVINGSTON 280, 2 AXIS HYDRAULIC, 2 HP, CHUCK, 1979 (7587) |
280 |
1979 |
8538
20" x 14" x 16" KIRA KN40VA 2 PALLET, 24" X 14" TABLES, 6,000 RPM, 10 HP, FANUC 21IM, 2000 (8538) |
KN40VA |
2000 |
8124
12” x 24” GALLMEYER #376, IDF, HYD DRSR, CP & T, 6” ADD’L HGT, 1981 (8124) |
370 |
1981 |
8410
12” x 24” OKAMOTO #ACCUGAR 124N, IDF, CP&T, OVER WHEEL DRESSER, 1979 (8410) |
ACCUGAR 124N |
1979 |
8310
12” x 24” OKAMOTO #ACCUGAR 124N SURFACE GRINDER,12" x 24" CHK, DRESSER |
124N |
1979 |
8811
12” x 24” GALLMEYER & LIVINGSTON #370, IDF, CP&T, 1967, (8811) |
370 |
1967 |
8755
24 STD RLM, 2" ARBORS, 12" RS, 5 1/2" VERT ADJ, DE REEL, SERVO FEED, PRE PIERCE PRESS, 2004, (8755) |
|
2004 |
8945
12" x 24" OKAMOTO MODEL ACC1224DXNC, FANUC OM CONTROL COOLANT W/ FILTER, DRESSER, 1997 (8945) |
1CC1224DXNC |
1997 |
8094
25 TON DIACRO #16-72 HYDRA-MECH BRAKE, 72” OA, 62” BH, 2” STROKE, 9” SHUT, 3 HP, (8094) |
16-72 |
|
8326
25 TON ROUSSELLE #3E, 4" STR, 14.25" SH, 20" x 14" BA, 135 SPM, 1994, (8326) |
3E |
1994 |
8373
25 TON ROUSSELLE #3, 2" STR, 10 3/4" SH,135 SPM, 20" X 14" BED, PALM BUTTONS,1984 (8373) |
#3 |
1984 |
8327
25 TON ROUSSELLE #3E, 4" STR, 14.25" SH, 20" x 14" BA, 135 SPM, 1994, (8327) |
3E |
1994 |
8474
25 TON ROUSSELLE #3 OBI, 2" STR, 10 3/4" SH, 14" x 20" BA, 135 SPM, 1990 (8474) |
#3 |
1990 |
8471
25 TON ROUSSELLE #3 OBI, 2" STR, 10 3/4" SH, 14" x 20" BA, 135 SPM, 1990 (8471) |
#3 |
1990 |
8777
25 TON BRUDERER # BS,TA-25, ADJ STR, 1500 SPM, 20 3/4" x 20 3/4" BA, BBV 190/85 FEED, 1976 (8777) |
BSTA-25 |
|
8472
25 TON ROUSSELLE #3 OBI, 1 1/2" STR, 10 1/4" SH, 14" x 20" BA, 150 SPM, (8472) |
#3 |
1965 |
8218
20" x 16" x 20" HAAS VF-0, 10,000 RPM, 26" x 14" TABLE, 710 IPM 20 POSITION ATC, BRUSHLESS SERVO, 15HP, 1997 (8218) |
VF-0 |
1997 |
8216
20" x 16" x 20" HAAS VF-0, 10,000 RPM, 26" x 14" TABLE, 710 IPM 20 POSITION ATC, BRUSHLESS SERVO, 15HP, 1997 (8216) |
VF-0 |
1997 |
8468
26" x 80" CLAUSING-BORAVIA SUS63H, 21" 4-JAW, TAPER, DRO, TOOLING, 1120 RPM, 1999 (8468) |
SUS63H |
1999 |
8217
20" x 16" x 20" HAAS VF-0, 10,000 RPM, 26" x 14" TABLE, 710 IPM 20 POSITION ATC, BRUSHLESS SERVO, 20HP, 1998 (8217) |
VF-0 |
1998 |
6922
25 TON EITEL #RP-25, 6” STR, 34” DAYLIGHT, 10” THROAT, 1986 (6922)) |
RP-25 |
1985 |
5640
30” x 18” x .054” COILMATIC #XHF-3018 RH, FEEDER/STRAIGHTENER, 1980 (5640) |
XHF-3018 RH |
1980 |
5301
30" x .060" 18" STR, AIR FEED INC #AF3, CABINET, PULL THRU STR, PINCH ROLLS, 1995 (5301) |
AF3 |
1995 |
6451
30 TON GREENERD HC-30-35R12, 12” STR, 24” DL, 26” X 16” BED, 1980 (6451)) |
HC-30-35R41 |
1980 |
7032
30 TON MINSTER # P2-30-20, 20” X 19” BED, 1 1/2” STR, 15” SHUT, 0 - 300 SPM, 10 HP, 1971 (7032)) |
P2-30-20 |
1971 |
8032
30” WIDE X 24” STR AIR FEEDS INC #AF4, 7 ROLL POWER STR, CABINET, NEW 1984(8032) |
AF4 |
1984 |
8182
30 TON HEIM #3A, 4” STR, 13 1/2” SH, 15” x 24” BA, 140 SPM, 1981 (8182) |
3A |
1981 |
8223
30 TON GREENERD HCA-30-30R8 HYDRAULIC PRESS, 12" STROKE, 18" DAYLIGHT, 24" X 26" BED,8-STATION ROTARY TABLE, 30" DIAMETER, 1994 (8223) |
|
1994 |
8791
30 TON STRIPPIT SUPER 30/30, 48” x 80” TABLE, 1 1/4” & 3” TOOL HOLDERS, GAUGE BAR, 1973, (8791) |
30/30 |
1973 |
8793
HAAS #SL30T CNC LATHE, 30" SWING, 39" CC, 3,400 RPM, 10" 3 JAW CHCK, 12 STAT TURRET, 2005, (8793) |
SL-30-T |
2005 |
8768
30 TON STRIPPIT CUSTOM 18/30, 18" THROAT, 1980, (8768) |
CUSTOM 18/30 |
1980 |
8803
30" x .110" LITTELL #PM30-7 STRAIGHTENER, 7 ROLL, 5 HP, VARI SPEED, LOOP CTRL, 2000 (8803) |
PM-30-7 |
2000 |
8897
30 TON STRIPPIT 30/30, 2 PUNCH HOLDERS, TOOLING, 1980 (8897) |
SUPER 30/30 |
1980 |
5150
12" x 32" CLAUSING/JAKOBSEN SJ0132 HYD SURF GRINDER, INC DN FD, WHEEL DRSR, 1984 |
SJ1032 |
1984 |
8487
16" x 32" OKAMOTO #1632N HYD, IDF, CHK AND CTRLS, CLNT, 5 HP, 1987 (8487) |
1632n |
1987 |
8563
32" x 120" GMTW, 39" GAP, 6 - 800 RPM, 4 1/8" HOLE, 15 HP, RAPID TRAVERSE, 1998 (8563) |
CW6280E |
1998 |
8427
33 TON STRIPPIT 1500 H/30 (2.5M), 61" X 100" SHEET, 40 TOOLS, 2AI , THIN TOOLING, FANUC 180i-P, 2000 (8427) |
1500/H/30 2 |
2000 |
8877
33 TON STRIPPIT #1000S, 33 STATION TURRET, 2 AUTO INDEX, FANUC OP, 1990 (8877) |
1000S |
1990 |
6440
35 TON BLISS C-35, 4” STR, 11” SH, 120 SPM, 26.5” X 17” BED, 1964 (6440) |
C-35 |
1964 |
7568
35 TON DENISON MODEL FL35 GAP FRAME, 15” STR, 24 3/4” DL, 30” x 20” BA, PALM BUTTONS, 1988 (7568) |
FL35-30H-C-592 |
1985 |
8517
35 TON PACIFIC TRI-ACRO #35-6 HYDRA-MECH, 6' OA, COMPUBEND CNC BG, 1993(8517) |
35-6 |
1993 |
7358
35 TON DENISON #FL35 GAP, 15” STR, 24 3/4” DL, 30” x 20” BED, CUSHION, PALM BTNS, PLC (7358) |
FL35 |
1967 |
5333
12" x 36" GALLMEYER & LIVINGSTON #550 HYD, INC DN FD, CHUCK, 1970 |
550 |
1970 |
6480
16” X 36” GALLMEYER #570, INCR DOWN FEED, CHUCK, 1981 (6480) |
570 |
1981 |
6962
16” x 36” GALLMEYER & LIVINGSTON #576 |
576 |
1977 |
7371
12” x 36” MATTISON, 15 HP, OWD, COOLANT, 24” WHEEL, 16” UNDER WHEEL, 1979 (7371) |
N/A |
1979 |
8122
12” x 36” GALLMEYER #550, IDF, 12” x 36” CHK AND CTRLS, CP&T |
550 |
1964 |
8123
14” x 36” GALLEMEYER #560, INCR DOWNFEED, CP&T, 1979 (8123) |
560 |
1979 |
5543
12” X 36” GALLMEYER & LIVINGSTON #550 HYD SRF GRINDER, ELEC CHUCK,, CLNT, 1978 |
550 |
1979 |
8477
36" x .093" COOPER WEYMOUTH PETERSON #36D7, 7 ROLL, 2.8" DIA, VS (8477) |
|
|
8558
36" X .090" LITTELL MODEL 436-7PD STRAIGHTENER, 7 ROLLS, ENTRY PINCH ROLLS, 3.125" ROLL DIAMETER, 12-72 FPM, 5 HP (8558) |
436-7PD |
1969 |
8620
36" BLANCHARD #18-36, 25 HP, 11" VERTICAL, 735 RPM, WET BASE, (8620) |
18-36 |
|
7853
37” AEM WET, #370 AMERICAN PRO, SPARE PARTS, 1994 (7853) |
all american pro |
1994 |
8682
37" TIMESAVER #237-3CMW, 1 BELT, 2 SCOTCHBRITE DRUMS, STAINLESS, WET, 1999 (8682) |
237-3CMW |
1999 |
8786
37" GRINDINGMASTER #2000 SERIES BELT GRINDER, 6" CAP, DRY, 20 HP, 1996 (8786) |
GR-2200-900-WB |
1996 |
8787
37" GRINDINGMASTER #2000 SERIES BELT & BRUSH GRINDER, 6" CAP, DRY, 20 HP, 1996 (8787) |
|
1996 |
8885
38.5 TON GUIFIL #PE15-35 HYD CNC, 60" OA, 53" BH, 4" STR, 12" DL, AUTOGAGE 2-AXIS, 1997 (8885) |
PE15-35 |
1997 |
8498
40" x 20" x 25" HAAS VF3, CLNT THRU SPDL, 7,500 RPM, CHIP AUGER, RIGID TAP, 1997 (8498) |
VF3 |
1997 |
8497
16" x 40" CLAUSING #CSG-1640SD, HYD, CP&T W/MAG SEP, SD CONTROL, 1997 (8497) |
CSG-1640SD |
1997 |
8282
40 TON REIS TUS115A/40HK UP-ACTING, 39" x 50" T-SLOTTED SHUTTLE TBL, SWING DOWN PLATEN, (8282) |
TUS115A/40HK |
1967 |
8395
40 TON ROUSSELLE #40H ADJ. BED, 4" STR, 5 1/4" - 16 1/4" SH, 26" x 16" BED, 105 SPM, 1997 (8395) |
40H |
1997 |
8511
40” x 20” x 25” HAAS VF-3, 7500 RPM, 15 HP, 20 POSITION ATC, ENCLOSURE, 1993 (8511) |
VF-3 |
1993 |
6452
40 TON GREENERD #H-40-35R14, 12” STR, 24” DL, 26” x 16” BED, 1974 (6452) |
H-40-35R14 |
1974 |
8643
40 TON ROUSSELLE #4B-60, 5" STR, 12 1/2" SH, 15 - 45 SPM VARI-SPEED, 60" x 18" BED (8643) |
4B-60 |
1987 |
8866
40 TON GREENERD #HC40-60 GAP, 24"STR, 48"DL, 850 IPM ADV, CUSHION, 26" X 16" BED, 1984 (866) |
HC40-60 |
1984 |
8867
40 TON GREENERD #HC40-60 GAP, 24"STR, 48"DL, 850 IPM ADV, CUSHION, 26" X 16" BED, 1986 (8867) |
HC40-60 |
1986 |
8933
44 TON EITEL #RP-40 HYD STRAIGHTENING PRESS, 55” x 11” TABLE, 6” STR, 34” DL, TBL EXT, TLNG, 1991, (8933) |
RP-40 |
1991 |
8942
40 TON PACIFIC #J-40-6 HYD, 6' OA, HURCO 5 CNC BG, 6" STR, 52" BH, 1978 (8942) |
J40-6 |
1978 |
7899
42” BLANCHARD MODEL 22K42, 50 HP, 24” VERTICAL, COOLANT IN BASE W/ CONVEYOR, DRESSER, (7899) |
22K-42 |
1970 |
8026
42” MATTISON MODEL 24-42 24” WHEEL, 42” CHUCK, 24” VERTICAL, 75 HP, EXTERNAL COOLANT, 1972 (8026) |
24-42 |
1973 |
8805
42" MATTISON #22-42 ROTARY, 75 HP, EXT CLNT, 1967 (8805) |
22-42 |
1967 |
8899
42” BLANCHARD MODEL 22K42, 50 HP, 24” VERTICAL, COOLANT IN BASE W/ CONVEYOR, DRESSER 1978 (8899) |
22K42 |
1978 |
8898
42” BLANCHARD MODEL 22K42, 50 HP, 24” VERTICAL, COOLANT IN BASE W/ CONVEYOR, DRESSER 1973 (8898) |
22K42 |
1973 |
8226
40" x 20" x 22" EXCEL #PMC-10T24 VMC, TRAVELS, 43" x 19" TABLE, 8,000 RPM, 40 TAPER, FANUC 21iM, 24 ATC, 1997 (8226) |
PMC-10T24 |
1997 |
7921
44 TON EITEL #RP-40 HYD STRAIGHTENING PRESS, 55” X 10 1/2” TABLE, 6” STROKE, 34” DAYLIGHT, BET. TABLE EXTENSIONS, FLOATING CENTERS, 1999 (7921) |
RP-40 |
1999 |
8529
44 TON EITEL #RP-40, 6” STR, 34” DL, 55” x 10 1/2” TABLE, TOOLING, 1990 (8529) |
RP-40 |
1990 |
8932
44 TON EITEL #RP-40 HYD STRAIGHTENING PRESS, 55” x 11” TABLE, 6” STR, 34” DL, TBL EXT, TLNG, 2004, (8932) |
RP-40 |
2004 |
8931
44 TON EITEL #RP-40 HYD STRAIGHTENING PRESS, 55” x 11” TABLE, 6” STR, 34” DL, TBL EXT, TLNG, 2004, (8931) |
RP-40 |
2004 |
5585
45 TON MINSTER #P2-45, 3” ST, 12 1/2” SH, 100 - 200 SPM, 25” X 32” BED, VAMCO FD, 1958 |
P2-45 |
1965 |
5946
45 TON KOMATSU #OBS-45, 3.94” STR, 80 SPM, 27.56” x 17.72” BED, 9.84” SH, 1979 |
OBS-45 |
1979 |
7665
45 TON HEIM 45-6, 2” STR, 12” SH, 40 SPM, 60” X 24” BED, 1986 (7665) |
45-6 |
1986 |
7824
45 TON FEDERAL, 3” STR, 11” SH, 120 SPM, 1978 (7824) |
45 |
1978 |
8387
45 TON MINSTER #5D, 3" STR, 15 3/4" SH, 150 SPM, AIR RAM ADJ, AIR C/BAL, 1974 (8387) |
5D |
1974 |
8384
45 TON L & J 45SS SPEED STAMPER, 3" STR, 13 1/4" SH, 110 - 330 SPM V/S, FLANGED RAM, 1985 (8384) |
45SS |
1985 |
4794
14" x 48" GALLMEYER & LIVINGSTON 660, IDF, 14" x 48" CHUCK, COOLANT, 1968 |
660 |
1968 |
8330
16" x 48" GALLMEYER & LIVINGSTON #670, INCR DOWNFEED, OWD, CP&T, 1974 (8330) |
7670 |
1974 |
8822
4' x 1/4" NATIONAL #NH4825 HYD, ROMBG, FRONT EXT, 2000 (8822) |
NH4825 |
2000 |
4609
50 TON DAKE 27-153 4-POST , 24"STR, 25"DL, 41" x 41"BA, 1970 |
27-153 |
1956 |
6044
50 TON NIAGARA SC2-50-48-24, 4 1/2" STR, 13" SH, 8" ADJ, 40 TO 100 SPM, UPDATED ELECT. (6044) |
SC2-50-48-24 |
1965 |
6263
50 TON DENISON#GP050 FOUR POST, 24" STR, 38" DL, 36" x 28" BETWEEN POSTS, 20HP, 1979 (6263) |
GPO50 |
1979 |
7591
50 TON HEIM MODEL 5-OBI-F, FLYWHEEL OBI PRESS, 4” STROKE, 12 1/2” SHUT, 4” ADJ, 120 SPM, 28” X 18” BED, 1982 (7591) |
50-OBI-F |
1982 |
8342
50" x 24" x 30" DEPO #MCFV-125, 6000 RPM, 50 TAPER, (2) 16 POS ATC'S, PALLET CHANGER, COOLANT THRU SPD, 1998 |
MCFV-123 |
1998 |
8457
50 TON RAPID PRESS, 48" x 36" DIE SPACE, 15" STR, 30" DL, 1979 (8457) |
|
1979 |
8530
50 TON DENISON #FMS-50 GAP, 12" STR, 20" DL, 320 IPM, 30 HP, LIGHT CURTAINS, 2001 (8530) |
FMS-50 |
2001 |
8706
50 TON EUROMAC #CX750/50 TURRET PUNCH, Y= 750 MM, X=1250 MM, NEW IN 2000 (8706) |
CX750/50 |
2000 |
8718
50 TON DENISON MODEL FN50-30H, 15" STROKE, 24 1/2" OPEN DAYLIGHT, 30 HP, PALM BUTTONS, HEAVY DUTY SERIES, 1981 (8718) |
FN 5030H-C590EPR |
1981 |
8799
50 TON WHITNEY MODEL 652 HYDRAULIC C-FRAME PUNCH, 30" THROAT, 2" STROKE, UP TO 1/2" THICK, 144" GAGE BAR, LOTS OF TOOLING, 1979 (8799) |
652 |
1979 |
7706
55 TON HEIM #5GA-F, 3” STR, 17” SH, 120 SPM, 18” X 24” BED, 1980 (7706) |
5GA-F |
1980 |
8074
55 TON DREIS & KRUMP 68-B, DUAL SPEED AIR CL, HURCO 5 CNC, LIGHT CURTAINS, 1963 (8074) |
68B |
1963 |
8919
55 TON PACIFIC #J55 HYDRAULIC, 8' OA, HURCO AB7 2 AXIS CNC, 1983 (8919) |
J55-8H |
1983 |
4954
CH-60 BLISS OBI FLYWHEEL PRESS, 4" ST, 13" SH, 32 X 21 BED, 100 SPM, 1967 |
CH-60 |
1967 |
4972
60 TON MINSTER P2-60-36, 4" STR, 14 1/2" SH, 36" x 25" BA, 100-200SPM, 1973 |
P2-60-36 |
1973 |
6259
60 TON ROUSSELLE 6A, 3” STR, 12 1/2” SH, 110 SPM, AIR CL AND BRAKE, 1979 (6259) |
6A |
1979 |
6405
60 TON MINSTER DYNAMIC, 4” STR, 90 TO 180 SPM, 16” SH, 32” X 21” BED, 1975 (6405) |
6D-1 |
1976 |
6524
60 TON ROUSSELLE 6G, 6G, 3” STR, 12 1/2” SH, 110 SPM, 30” X 18” BED, 24” THROAT, 1978 (6524) |
6G |
1978 |
7135
60 TON FEDERAL 2-60G, 4” STR, 25-60 SPM, 24” X 60” BED, 18” X 54” RAM, 15” SH, ACB, 1983 (7135) |
2-60G |
1983 |
7683
60 TON MINSTER #6, 4” STR, 120 SPM, 32” X 21” BED, AIR C/B, 1990 (7683) |
6SSFB |
1990 |
7684
60 TON NIAGARA M-60, 4" STR, 14" SH, 32" x 21" BED, 100 SPM, A.C., 1978 (7684) |
M-60 |
1978 |
6564
60 TON ROUSSELLE #6, 4” STR, 11.5” SH, 3” ADJ, 18” x 30” BA, 110 SPM, ELECTRIC FOOT SWITCH, DUAL PALM BUTTONS. |
6 |
1974 |
7229
60 TON MINSTER #6SSFB, 4” STR, 15.5” SH, 32” x 21” BA, 90-180 SPM, 1990 |
6 |
|
8248
60 TON BLISS C-60, 1" STR, 15 3/4" SHUT, 3" ADJ, 60 SPM, BACK GEARED, 32" X 21" BED (8248) |
C-60 |
1973 |
8181
60 TON L & J, BACK GEARED, 4” STR, 13” SH, ISB PC100 PRESS CONTROLS, WINTRESS, V/S, (8181) |
N/A |
1967 |
8519
30" x 15" x 16" HURCO #MD1 VMC, DUAL SCREEN CNC, 12 POS ATC, #40, 1986 (8519) |
md1 |
1986 |
8765
60 TON ACCURPRESS #76010 HYD, 10' OA, PERM FLANGED BED, 1984 (8765) |
76010 |
1984 |
8319
66 TON AIDA #NC1-6(1), 3.54" STR, PRA, HYD OVERLOAD, 60-120 SPM, 1986 (8319) |
NC1-6 |
1986 |
8896
66 TON AMADA TP-60EX GAP PRESS, 4.72" STR, 16.34 SH, 36" x 22" BED, 45 - 85 SPM, HYD OVERLOAD, 2004 (8896) |
TP-60 |
2004 |
6454
70 TON BLISS OBG-70, 4” STR, 15.5” SH, 32” X 21” BED, 17” X 12.7” SLIDE, 60 SPM, 1987 (6454) |
OBG-70 |
1987 |
7935
70 TON ROUSSELLE #B1-70, 4” STR, 12 1/2” SH, 110 SPM, 32” x 21” BA, AIR COUNTER BAL, PLC CONTROLS, 1994 (7935) |
B1-70 |
1994 |
8663
70 CUBIC FT SWECO VIBRATORY FINISHER, 20 HP, CONVEYOR LOAD AND UNLOAD, 1979 (8663) |
70FM |
1979 |
7119
6’ x 10 GA CINCINNATI 1006R, 36” FOPBG, SQUARING ARM, 1977 (7119) |
1006-R |
1977 |
8751
6' x 1/4" CINCINNATI #1806G MECH, 36" FOPBG, MICRO GAGE, 1998 (8751) |
1806RG |
1998 |
8749
6' x 1/4" CINCINNATI #1806RG MECH, 36" FOPBG, 1997 (8749) |
1806RG |
1997 |
8758
6' x 1/4" CINCINNATI #1806RG MECH, 36" FOPBG, MICRO GAGE CONTROL, 1998, (8758) |
1806RG |
1998 |
8848
6' x 10 GA. ACCURSHEAR #81356, HYD, 24" FOPBG, SQ ARM, 1990 (8848) |
81356 |
1990 |
8870
72 TON PEDDINGHAUS MODEL 210 SUPER 13, MECH, 5" x 5" x 1/2" ANGLE, 8" x 1/2" FLATS, 1 1/16" PUNCH, LOTS OF TOOLING, 1981, (8870) |
210 SUPER 13 |
1981 |
8886
6' x 3/16" WYSONG MODEL 772 MECHANICAL SHEAR, 10GA. STAINLESS, 36" F.O.P.B.G., SQUARING ARM, (2) FRONT SUPPORT ARMS, 1986 (8886) |
|
1986 |
7356
75 TON MINSTER MODEL 7D-SS FLYWHEEL TYPE, 4” STROKE, 21” SHUT, 90 SPM, FLANGED RAM, RECIRC LUBE, 1982 (7356) |
7D-SS |
1982 |
7604
75 TON MINSTER #7 GAP, 6” STR, 19” SH, 60 SPM, 36” x 24” BA, CUSH, 1989 (7604) |
#7 |
1989 |
7605
75 TON MINSTER #7, 6” STR, 19” SH, 45 SPM, 36” X 24” BED, WINTRESS LOAD MONITOR, 1978 (7605) |
#7SS
|
1978 |
7846
75 TON NIAGARA B4-42 DOUBLE CRANK GAP FRAME PRESS, 42” X 20” BED, 5” STROKE, 12 1/2” SHUT, 100 SPM, AIR CB, 1976 (7846) |
B4-42 |
1976 |
8291
75 TON DENISON #FQ-75-40 HYD, 17 3/8" STR, 36" DL, AB SLC 504 CTRLS, 1987, (8291) |
FQ-75/G-592E |
1987 |
8292
75 TON DENISON #FQ-75-40 HYD, 17 3/8" STR, 36" DL, AB SLC 504 CTRLS, 1987, (8292) |
FQ-75/0592E |
1987 |
8678
75 TON BLISS SSDC, 8" STR, 20" SH, 37 SPM, UPDATED ELEC, 19" WINDOWS, SERVO FEED LINE, 1953, (8678) |
S2-75 |
1953 |
8739
75 TON CINCINNATI #3 MECH, 8' OA, 6'6" BH, 3" STR, PWR RAM ADJ. (8739) |
#3 |
1963 |
8930
77 TON GEKA #HYDRACROP-70S IRONWORKER, 5 x 5 x 1/2 , 18" x 5/8" SHEAR, 2" x 3 1/2" x 15/32" NOTCH, TWIN CYLINDER, 1990 (8930) |
HYDRACROP-70S |
1990 |
8466
88 TON KOMATSU #80S-VS-3, 5.12" STR, 13.78" SH, 37-75 SPM, 39" x 24" BED, 1997 (8466) |
OBS-80S-VS-3 |
1997 |
8516
90 TON PACIFIC #J90-8 HYDRAULIC, 8' OA, 78" BH, 7" STR, 1992 (8516) |
J90-8 |
1992 |
8547
90 TON PACIFIC #FF90-12 IIS, 12' OA, 10'6" BH, CYBELIC DNC 60 3 AXIS BG, 1988, (8547) |
FF90-12 IIS |
1988 |
8895
90 TON PACIFIC J90-8 HYDRAULIC, 8' OA, 78" BH, 7" STROKE, 13" OPEN, LOWER DIE HOLDER, RAM CLAMPS, PALM BUTTONS, 1980 (8895) |
J90-8 |
1980 |
8914
90 TON CINCINNATI #CB90X8 HYD, 10' OA, HURCO 7 2 AXIS BG, MCH FOR ANGLES, 1986 (8914) |
CB90X8 |
1986 |
7257
20” X 96” MATTISON, OVER WH DRESSER, 30 HP, POWER ELEV. (7257) |
N/A |
1954 |
8762
8' x 1/4" CINCINNATI #1808 AUTOSHEAR, FOPBG, 1999, (8762) |
1808 |
1999 |
8072
100 TON NIAGARA PN-100-120-24, 3” STR, 5” AD, 18” SH, 40 SPM, 18” WINDOWS, 1989 (8072) |
PN-100 |
1989 |
8354
100 TON BLISS HP2-100, 42" X 30" BED, 4" STR, 17" SH, 70 - 120 SPM , NEW CONTROLS, 1965 (8354) |
HP2-100 |
1965 |
8475
100 TON REIS #TUS1150K-100, 32" X 50" BED, TILT RAM, WAX INJ, 1983 (8475) |
TUS150K-100 |
1983 |
8513
100 TON MINSTER #P2-100-54, 2" STR, 18" SH, 80 - 160 SPM, 1955, (8513) |
P2-100-54 |
1955 |
8514
100 TON ROUSSELLE #10SS100, 6" STR, 18.5"SH, 50 SPM, 30" x 100" BA, LINK ELTRCS, 2001, (8514) |
10SS100 |
2001 |
8011
100 TON DAKE 4 POST, 120” x 72” SLIDING BOLS, DROP DOWN RAM, 60” STR, 84” DL, 1975 (8011) |
18-641 |
1975 |
8512
100 TON REIS T115-100, 39" x 50" BED, TILT BOLS, DROP DOWN TOP PLATEN, WAX INJ, 1970 (8512) |
T115 |
1970 |
8684
100 TON PACIFIC PRESSFORMER II HYDRAULIC PRESS, 18" STR, 32" DL, 35" x 18" BED, LIGHT CURTAINS |
100 |
1999 |
8920
100 TON PACIFIC #100-8, 8' OA, 6'4" BH, AUTOBEND TWO AXIS HURCO 5 CNC BG, 1970 (8920) |
100-8 |
1970 |
5199
110 TON CLEARING OBI (GAP) PRESS, 10" STR, 24" SH, 42" x 27" BA, 42-82 SPM, 1970 |
110 |
1970 |
5833
110 TON MCKAY WARCO #G-110-1, 6” STR, 17” SH, 35 SPM, 40”X30” BA, AIR CL, CUSH, 1967 |
G-110-1 |
1967 |
7548
110 TON LVD MODEL BH12 HYD BRAKE, 157” OA, 120” BH, 6” STRK, 13 3/4” OPEN HEIGHT, 1973 (7548) |
BH12 |
1973 |
8421
10' x 1/4" NIAGARA #810 MECH SHEAR, 36" FOPBG, 84" RH SQU ARM, 1977 (8421) |
810 |
1977 |
8653
10' x 1/4" NIAGARA #1F-10-1/4 HYDRAULIC SHEAR, FOPBG, SQU ARM, 1984 |
IF-10-1/4 |
1984 |
8752
10' x 1/4" CINCINNATI #1810G MECH, 36" FOPBG, MICRO GAGE CONTROL, NEW 2000 (8752) |
1810G |
2000 |
8753
120 TON PREMIER #1012-R HYD, 120" OA, 100" BH, 8" STR, 15" DL, HURCO 7 3-AXIS CNC, 2001 (8753) |
1012-R |
2001 |
7664
10’ x 1/2” HURCULES HYD, 36” FOPBG, FLOOR STD, 1978 (7664) |
N/A |
1978 |
8584
10' x 1/2" NIAGARA #IF-10 1/2 II, HYDRAULIC, 36" FOPBG, SQU ARM, 1993 (8584) |
1F-10 1/2 II |
1993 |
8702
10' x 1/4" CINCINNATI #1810G MECH, 36" FOPBG, SQ ARM, FRNT SPTS, 1995, (8702) |
1810G |
1995 |
8821
120 TON GEKA #110/SD HYDRAULIC, 6" x 6" x 1/2", NOTCHER, BAR SHEAR, (8821) |
110/SD |
1998 |
8834
10' x 3/8" CINCINNATI #3D10 HYDRAULIC, FOPBG, SQ ARM, CONVEYOR, 1976 (8834) |
3D10 |
1976 |
8835
120 TON ROUSSELLE #G-120-4 GAP, 6" STR, 16.5" SH, 90 SPM, 40" x 30" BA, 1998 (8835) |
G-120-4 |
1998 |
8912
10' x 1/4" CINCINNATI #1810G, FOPBG, MICRO COMPUTER CTRLS, SQ ARM, 1994 (8912) |
1810G |
1994 |
8961
10' x 1/4" NIAGARA #88, FOPBG, LH SQ ARM, 2 FRONT SUPORTS, 1952 (8961) |
88 |
1952 |
7292
121 TON GREENERD MODEL HTC-110 HYD PRESS, 10” STROKE, 18” DAYLIGHT, 32” X 28” BED, 14” WINDOWS, 295 IPM ADVANCE, PROGRAMMABLE CONTROL W/ POSITION AND DWELL, 1983 |
HCT-110 |
1983 |
5714
125 TON SB/JOHNSON #125-BGAC, 4” ST, 17 1/2” SH, 27” X 42” BED, 40 SPM, AIR CL, 1975 |
125-BG-AC |
1975 |
8828
15 HP QUINCY #QEH-15-120, 2 STAGE, 52 CFM, 120 GAL. TANK |
QEH-15-120 |
1990 |
7919
135 TON CINCINNATI 5X6, 8’ OA, AIR ACTUATED MECH CL, ENCLOSED GEARS, PRA, 1975 (7919) |
5X6 |
1975 |
8960
135 TON CINCINNATI #135CB X 10, 12' OA, MANUAL BG, DIE RAIL, 1989 (8960) |
135CB |
1989 |
8798
12' x 1/4" CINCINNATI #250HS12 HYDRAULIC, SQ ARM, MICRO GAGE BG CNTL, 1997 (8798) |
250HS12 |
1996 |
8820
12' x 1/4" WYSONG #H-2512 HYDRAULIC, PC100 CNC BG, PWR BLADE GAP ADJ, SQ ARM, 1996 (8820) |
H-2512 |
1996 |
8883
12' x 1/4" ACCURSHEAR #625012, HYD, FOPBG, SQ ARM, 1996 (8883) |
625012 |
1996 |
8935
12’ x 1/4” CINCINNATI #2CC12, 36” FOPBG, MICROCOMPUTER GAGE, SQ ARM, FRT SPRT, 1990 |
2CC12 |
1990 |
8876
12' x 1/4" CINCINNATI #1812 MECH, SQ ARM, FOPBG, SUPPORTS, 1968 (8876) |
1812 |
1968 |
5308
150 TON MINSTER #P2-150-48, 2" ST, 22" SH, 48" X 40" BED, SRF, 100 - 200 SPM, 1968 |
P2-150-48 |
1968 |
5807
150 TON BLISS #SG2-150, 12” STR, 32” SH, 40 SPM, 60” X 30” BED, A/CL, A/C/B, 1965 |
SG2-150-30-60 |
1965 |
5931
150 TON BLISS S2-150-60-42, 8” STR, 8” ADJ, 30 TO 60 SPM, 1969 |
S2-150 |
1970 |
6083
150 TON RAVNE SSDC PRESS, 7.9” STR, 18.5” SH, 60” X 42” BA, 50-100 SPM, 1990 (6083) |
UHS-150-60-42 |
1990 |
7273
150 TON JOHNSON #150BC-AC, 6” STR, 21” SH, 50” X 30” BED, 34” X 24” RAM, 1980 (7273) |
150BG-AC |
1980 |
8023
150 TON OTC, H-FRAME, ADJUSTABLE ROLLING BED, 15" STR., 48” B/T UPRIGHTS, MOVEABLE HEAD, (8023) |
N/A |
|
8882
150 TON MINSTER MODEL P2-150-42, 4" STR, 17" SH, 50-150 SPM, WINTRISS SMART PAC2 (8882) |
P2-150-42-40 |
1962 |
8770
175 TON CINCINNATI #175FMII x 6 HYD, 8' OA, 6'6" BH, PERM FLANGED, 1991 (8770) |
175 FMII |
1991 |
8442
175 TON WYSONG #MTH175-144, 12' OA, 10'6" BH, 8" STR, AUTOGAGE 2-AXIS CNC BG, LITE CURTAINS, 1996 (8442) |
MTH175-144 |
1996 |
8875
175 TON ACCURPRESS #717512 HYD, 12' OA, 8" STR, ETS 100 CONTROL, LOWER DIE HOLDER, 1997 (8875) |
717512 |
1996 |
7825
200 TON DAKE, 12” STR, 22” DAYLIGHT, 30” X 30” PLATENS, UPACTING, 1970 (7825) |
33-345 |
1970 |
8073
18' x 3/16" CINCINNATI #2518 MECH, 36” FOPBG, 10’ LH SQ ARM, FRONT SUPPORTS, 25” GAP, 1960 (8073) |
2518 |
1960 |
5409
225 TON DREIS & KRUMP #225-D6, 6” ST, 24” SH, 24” X 96” BED, 30 SPM, A/CL, 1975 |
225-D6 |
1975 |
8775
225 TON CINCINNATI #9X10 MECH, 12' OA, MECH CL, REMOVEABLE FLG, 1975, (8775) |
9X10 |
1975 |
8623
230 TON PACIFIC #230FF-12-11S, 12' OA, CYBELEC 3 AXIS CNC, FLOOR STANDING, 1993 (8623) |
230FF |
1993 |
8782
230 TON CINCINNATI #230CBx12 HYD, 14' OA, 12'6" BH, 10" STR, 1984 (8782) |
230cbx12 |
1984 |
8772
230 TON CINCINNATI #230FMII x 10 HYD, 12' OA, 10'6" BH, FORM MASTER CONTOLS,1991, (8772) |
FMIIX10 |
1991 |
8771
230 TON CINCINNATI #230FMII x 10 HYD, 12' OA, 10'6" BH, FORM MASTER II CTRLS, 1991, (8771) |
230fmIIx10 |
1991 |
4569
250 TON PACIFIC #250PF -OBS GAP, 12" STR, 21.75" DL, 58" x 34" BED, 1984 |
250PF-OBS |
1984 |
8030
250 TON USI CLEARING 84X54, 12” STR, 12” ADJ, 40” SH, 20 TO 40 SPM, FLOOR STD, 1976 (8030) |
S2-250 |
1976 |
5736
250 TON PACIFIC #250PF-OBS HYD GAP, 12” STR, 21.75” DL, 58” x 34” BED, 1982 (5736) |
250PF-OBS |
1982 |
8455
275 TON AIDA #C2-25(2), 11" STR, 21.6" SH,120" x 36.2" BA, 30 SPM, 82.6" x 27.5 RAM, 1986 (8455) |
C2-25(2) |
1986 |
8456
275 TON KOMATSU OBW-250-2, 11.8" STR, 106" x 37.4" BA, 30 SPM, 21.65" SH, 1984 (8456) |
OBW-250-2 |
1984 |
8748
300 TON DAKE #27-227 4-POST, 48" STR, 60" DL, 60" x 55" DIE SPACE, AB 550 PANEL VIEW, 1961 (8748) |
27-227 |
1961 |
8900
300 TON PACIFIC #300-10 HYDRAULIC, 10'OA, 8'5" BH, 12" STR, 20" OPEN, MANUAL BG, 1955, NEW HYDRAULICS/CONTROLS IN 1976 BY PACIFIC (8900) |
300-10 |
1955 |
8929
300 HP QUINCY #SII5ACA3SC-1500 SERIES SCREW TYPE, 125 PSI, 1515 CFM, 22,000 HRS, 1992, (8929) |
SII5ACA3SC-1500 SERIES |
1992 |
8534
400 TON MINSTER MODEL 90-400 KNUCKLE JOINT PRESS, 4" STROKE, 13 1/2" SH, 28"X21" BED, 45 SPM (8534) |
90-400 |
1962 |
8677
440 TON KOMATSU E2G, 16.1" STR, 20-40 SPM, 122" x 61" BED, 63" WINDOWS, FEEDLINE, 2000 (8677) |
E2G |
2000 |
8640
500 TON DAKE 4 POST HYD, HVY DUTY, 30" STR, 36" DL, BA 42" x 50", 1979, (8640) |
23-379 |
1979 |
7239
600 LB. P.A. INDUSTRIES MODEL DSRA-600DSP DOUBLE END REEL, 8” WIDTH, 8”-18” ID, 48” OD, PLAIN, AIR BRAKES, KEEPER DISCS, 1995 (7239) |
DSRA-600D-SP |
1995 |
8481
600 LB. DURANT #DSC-1 PLAIN COIL REEL, 10" W, 44" OD, 1997, (8481) |
DSC-1 |
1997 |
8458
750 TON PACIFIC #500-OBL-12, 150" X 72", 24" STR, 60" DL, CUSHIONS, PLC 1996 (8548) |
500 OBL 12 |
1996 |
7622
1,000# ASL MODEL 70 DBL END PLAIN, 12” WIDE 13”-21” ID, 60” OD, 16” FACE, BRAKES, 1993 |
70 |
1993 |
3457
1200# COOPER WEYMOUTH MOTORIZED SINGLE END, 15"-18"ID, 48"OD, 18"W |
1200-18M |
1965 |
7627
1,200# ASL MODEL 70 DBL END PLAIN, 12” WIDE,13”-21” ID, 72” OD, 16” FACE, AIR BRAKES, 1993 |
70 |
1993 |
8723
1,600# COOPER WEYMOUTH PETERSON #2RD, DOUBLE END, NON MOTORIZED (8723) |
2RD |
|
4178
1600 lLB. COOPER WEYMOUTH PLAIN COIL REEL, 16"-20" ID, 18" WIDE, 48” OD, ELECT BRAKE |
|
1978 |
7634
2,000 LB. X 12” WIDE LITTELL MODEL 20-12 PLAIN REEL, 16”-20” ID, 48” OD, 18” FACE, BRAKE, 1976 (7634) |
2-20-12 |
1976 |
7476
2500 LB PERFECTO 12-M-D8, PLAIN DOUBLE END, (7476) |
12-M-DB |
|
7497
2500 LB. PERFECTO 15-4B2500DR PLAIN DOUBLE END (7497) |
15-4B2500DPR |
|
7832
2,500# COE CPR-DE 2512 DOUBLE END PLAIN, 12" W, 16”-21” ID, 54” OD, ROTATION, KEEPERS, 1987 (7832) |
CPR DE 2512 |
1987 |
8177
2,500# LITTELL #25-18 DOUBLE END PLAIN, 18" W, 16” - 20” ID, 48” OD , 1973 (8177) |
25-18 |
1973 |
6665
3,000# x 20” ROWE MODEL 3020J COIL CRADLE, 3000 LBS, 20” WIDTH, 48” OD, 35 - 100 FPM, 1 HP (6665)) |
3020J |
1969 |
6735
3,000# x 20” x .105” ROWE MODEL B20-C3000J CRADLE / STRAI, 48” OD, 35 - 100 FPM, 3 HP, 7 ROLL STRAI, 1979 |
B20-C3000J |
1977 |
8662
3,000 WATT BYSTRONICS #BYSTAR 3015, 5' x 10', DUAL PALLET, LOAD/UNLOAD, 1999 (8662) |
BYSTAR 3015 |
1999 |
7226
4,000# PERFECTO #12-M-DB DBL END PLAIN REEL, 12” W, 60”OD, MAG DRAG BRAKE, |
12-M-DB |
1978 |
8696
3,500 LB COILMATE MODEL CM3042 PALLET TYPE UNCOILER, 42" OD, 6" X .065" MATERIAL, 37" STACK HEIGHT, 0 - 23 RPM DC DRIVE, 1994 (8696) |
CM3042 |
1993 |
8695
3,500# COILMATE #CM3042 PALLET UNCOILER, 42" OD, 0 - 23 RPM DC DRIVE, 1994 (8695) |
CM3042 |
1994 |
6785
4000 LB. PERFECTO RD4-12B, DOUBLE END, 12” WIDE, ADJ BASE, HYD EXP, BACK PLATE, 1992 (6785) |
RD4-12B |
1992 |
7148
4,000# ROWE #4020 DSV MOTORIZED REEL, 20”W, 60” OD (7148)
|
4020-DSV |
1971 |
4193
4,000# LITTELL 40-24 SINGLE END PLAIN, 12"-14"ID, 45"OD, 24"W, 1962 (4193) |
40-24 |
1962 |
7933
4,000 LB LITTELL 40-24 SINGLE END NON-MOTORIZED, 1958 (7933) |
40-24 |
1958 |
8014
4,000 LB LITTELL #40-12, DOUBLE END, NON-POWERED, 12” WIDE, 60” OD, BACK PLATE, ELECT BRAKES, 1967 (8014) |
40-12 |
1967 |
8035
4,000 LB X 12” LITTELL MODEL 40-12 DOUBLE END PLAIN REEL, 15” - 20” ID RANGE, 60” OD, FULL BACK PLATES, AIR BRAKE, (8035) |
N/A |
1964 |
7934
4,000# FEED LEASE MODEL PR-4M-24 MOTORIZED, 24” W, 16”-21” ID, 60” OD, LOOP CONTROL, KEEPERS, 1986 |
PR-4M-24 |
1986 |
8570
4,000 LB. LITTELL 40-12 DOUBLE END, AIR BRAKES, BACK PLATE, 1991 (8570) |
40-12 |
1991 |
6545
5,000 LB. X 24” WIDE X .200, REGAL MODEL 3207-CC/SS24 7-ROLL STR, 50” OD, 125 FPM, VARIABLE SPEED, 3 HP, 1976 (6545)) |
3207-CC/SS24 |
1979 |
7638
6,000 LB X 12” WIDE REGAL POWERED REEL, 14” - 21” ID, 60 OD, 5 HP DRIVE, LOW $$, 1976, (7638) |
6000-12-SRP-HD-AR |
1976 |
8036
6000 LB AMERICAN STEEL LINE POWERED, 24” WIDE, 72” OD, 1979 (8036) |
|
1979 |
8081
6,000# ASL POWERED UNCOILER, 30” W, 15 1/2” - 20 1/2” ID, 60” OD, FULL BACK PLATE, LOOP CONTROL |
1000 |
1970 |
6658
6,000# x 12” JAYBIRD CRADLE |
60-12 |
|
8250
6,000# ASL #1000 MTRZD, HYD EXP, COIL CAR 36" WIDE, 60" OD, 1984 (8250) |
1000 |
1984 |
8508
6,000# ASL #1000, 30"W, 15.5" - 20.5" ID, 60" OD, VARI SPEED, LOOP CTRL, KEEPERS, 1972, (8508) |
1000 |
1972 |
8553
6,000 LB AWC MODEL D600 PALLET TYPE, .050" -.50" WIRE, 64" OD, 18" - 32" ID, 1 1/2 HP, 0 -35 RPM, LOOP CONTROL SYSTEM (8553) |
D600 |
1990 |
8556
6,000 LB AWC MODEL D60F PALLET TYPE, FLAT STOCK UP TO 16" WIDE, 72" OD, 16" - 44" ID, 1 1/2 HP, 0 -35 RPM, LOOP CONTROL SYSTEM, 1994 (8556) |
D60F |
1994 |
8789
6,000# AWC MODEL D60 PALLET TYPE, 72" OD, 0 -35 RPM, LOOP CONTROL SYSTEM, 1997, (8789) |
D-60F |
1997 |
8783
6,000# AIR FEEDS #R60 MTRZD, 18" W, 60" OD, LOOP CTRL, 1994, (8783) |
R-60
|
1994 |
8857
6,000# COILMATE #CM6060 PALLET UNCOILER, 60" DIA, 1998 (8857) |
|
1998 |
8161
7,000 LB YALE #GL0070LCNSBE085 LP GAS LIFT TRUCK (8161) |
GL0070LCNSBE085 |
1993 |
7623
10,000# CWP MOTORIZED REEL, 36” W, 15 1/2” -20 1/2” ID, 72” OD, 5 HP, ELECTRIC BRAKE, 1986 |
CWP1000036M |
1986 |
8085
10,000# ASL UNCOILER, 30” W, POWERED, HYD EXPANSION, 15 1/2” - 20 1/2” ID, 60” OD, VARI-SPEED, 1980 (8085) |
1000 |
1977 |
8263
10,000# FEEDLEASE #10M18 REEL, CAR, HYD EXP, THRD DRV, 18" x .100" 7 ROLL STR, AIR FEED, 1987 (8263) |
|
1987 |
8264
10,000# FEEDLEASE #10M18 REEL, CAR, HYD EXP, THRD DRV, 18" x .100" 7 ROLL STR, AIR FEED, 1987 (8264) |
|
1987 |
8262
10,000# FEEDLEASE #10M18 DBL END, CAR, 18" x .100" 7 ROLL STR, AIR FEED, 1987 (8262) |
10M18 |
1987 |
8863
10,000 LB LITTELL #620D-5PD-C100, 20" WIDE x .156" CAPACITY, 60" OD, 1972 (8863) |
620D-5PD-C100 |
1972 |
8849
10,000 LB AIR FEEDS INC #R100, 36" W, POWER, HYD EXP, HOLD-DOWN, AIR CL, 1984 (8849) |
R-100 |
1984 |
8913
10,000# DALLAS DPR-10000-24 MOTORIZED, HYD EXP, HOLD DOWN ARM, AIR BRAKE, 1996 (8913) |
DPR-10000-24 |
1996 |
8659
20,000# AMERICAN STEEL LINE, 72" WIDE, POWERED, HYD EXP, COIL CAR (8659) |
1000 |
1984 |